Search results

stock 99 AW4. No slippage etc but when comes to a stop it will not pull off unless manually shifted into low. You can feel it try to pull but it wont until dropped down to low. Run it thru the gears manually and you can drive it anywhere. Any ideas?

if ya haven't take the time and $ to do it.... a hours time and $55 at Orielly for a BWD brand IAC valve and a can of TB cleaner makes for a much smoother idling XJ. I had previously sprayed the TB while on the engine. Thought I had it cleaned out pretty well but still had a rough idle. Not...

Im swapping a 94 AW4 into a 97 XJ and would like to swap the 97 solenoid harness onto the 94 trans instead of cutting and buttsplicing it. Am I going to have to drop the pan and undo the wires directly from the solenoids, or does the plug where it goes in the case come apart and not have...

got a buddy with a 01 that needs a shifter gate with the 242 pattern... email [email protected] if ya have one thanks.

Have a set of light grey leather seats, power drivers. .... Have a cpl of seams coming apart but otherwise in good condition. Located in Birmingham AL......... will not ship........... $200 or swap for some decent used 30x950x15 or 31x1050x15 or maybe a firearm. I have them in storage a...

Finally have my long armed 01 project almost done so its time to sell my 93. 4 door, black in color, 6cyl , auto, a/c, manual windows/locks, 231 T/case.... stock axles, 30/8.25, stock gearing, and bumpers. Has flowmaster muffler and dual tail pipes. Sits on about 4" of lift with rubicon...

looking for some decent carpet for a 97-01 2 door XJ

Found me a 00 WJ today at the pullapart while there pulling some other parts for a porject. Came home with complete knuckles with rotors and calipers. $70 for everything otd. After reading a ton of different posts I haven't found my answer. Every write up I found was changed to OTK and...

Looking for 97-01 front fenders, header panel with grille bezels etc. Front bumper and end caps. if anyone has any of these let me know. Im open to buying a whole parts car if someone has one reasonably priced. Title is not needed for it. I will drive withen 4 hours of birmingham to...

looking for some stock steel or factory alloy rims...... anything but the honeycomb style....... I travel from Birmingham thru jackson miss to Monroe La. every couple of weeks....... so if anyone that far away along that route has some too let me know.

looking for dark blue grill and headlight bezels for a 97 up...... also painted fender flares same color.

picked up a 97 2wd today with a bad trans..... anyone have a 2wd tranny, or a 4 wheel drive tranny with transfer case laying around ? Im located in Birmingham but will drive to Pu.

woodgrain bezel that goes around the radio and center a/c vents.... perfect condition $35+ shipping. Looks like this...

Factory skid for pre 97 model.....perfect condition. Would like to trade for a 97 up tank skid or will sell for $85...... prefer local pick up on it.

Class 3 receiver hitch for a XJ.... $65

Found a guy with one NIB locally for $75...... wasnt planning on getting a header but for the price I may try it since I have the dynomax cat back system waiting to go on also. I googled but found very little info. Anyone else running one of these? pros? cons?

have a class 3 hitch for a XJ..... $50

need a red passenger fender 97 up........ doesnt have to be a 10 but no junk. closer to Birmingham alabamathe better.

heres the deal.... got a RC long arm kit with 4.5 RE coils and 3/4" spacer waiting to go on. (spacer to overcome winch bumper weight) After looking at the RE website for their 4.5" lifts they are using 3.5" springs and a 1" lift shackle to get that height on their 4.5" kit. My goal is...

found a stock 98 2 hours away for sale the guy says wont shift into OD......hes been driving it 3 months this way. Says it shifts thru other gears fine... any ideas before I make the drive ?