Search results

1989 Jeep Cherokee XJ 2 door flat black. 4.0 Renix engine w/ about 220,000 miles. 4x4, 5spd Peugeot BA 10/5 transmission. 4.5" rustys lift. 33" tires (5). Transfer case drop. Custom front bumper w/ XRC-8 winch. Chrysler 8.25 rear axle. Dana 30 front axle. (Both w/ 3.55 gears) JKS quick...

So I just recently swapped out my dana 35 for an 8.25, everything is all hooked up,the swap went fine. But on the passenger side rear leaf there's a gap in between the top and second to top leaf. Any ideas of why this would happen? And how I can fix it? Any help at all would be great, thanks.

Next week I'll be swapping my front and rear axles. Front with another dana 30 and rear with a 8.25 . Are there any write ups on how to do this? Any advice on how to make this process go smoothly? Any help at all would be great. Thanks

So the previous owner used my rig for strictly off road purposes and it currently doesn't have A/C or heat. He said when I purchased it that he had removed the condenser. To regain A/C do I only have to replace the condenser and it will work again? I don't know much about A/C at all, so this is...

There was a site for the SYE kits posted a little while and I can't seem to find it. On the site you have the choice to just buy the SYE by it self, or buy the drive shaft by it self, so on and so forth. If anyone can help with navigating me to this site that'd be great. Also, I have a Dana 35...

So recently the heep has been creeping up to 220* while driving for about 30 minutes or so but never really goes further and overheats. Any reason for this to be happening? I just don't want this to cause a problem for me in the future. Anything I can do to not have this happen and the keep the...

So recently i've discovered my brake lights are no longer working. The tail lights as well as the turn signals are still working, but not the brake lights. Any idea of what would cause this and what I can do to fix the problem? Any help at all would be greatly appreciated. Thanks!

The crossmember bolts keep poppin out after about 2-3 weeks. Is there a certain way to keep them up and not move? I'm tired of installing new bolts and have them pop out a couple weeks later. Any suggestions are appreciated. Thanks

Just recently I started experiencing some problems with the RPMs when I push in the clutch to shift. Doesn't happen all the time, but lately more so than not.. What happens is I'll push in the cluth to shift and the RPMs will shoot up to anywhere between 2-5k but as soon as I shift gears it...

So recently I've been hearing and feeling a clunking noise under the driver side footwell. Between 35-45 mph is when it's most noticable, but I can still hear and feel it at any speed. Any ideas of what it is? :dunno: Thanks

Was just wondering, does anyone on here drive without a track bar? My buddy said he used to drive without it on his heep.

I've gone through 3 u-joints on the rear driveshaft(axle end) in the last month and a half or so and it's starting to get ridiculous. Does anyone know what might be causing this? I grease them up every time I install one. I can't seem to figure it out. Any help at all would be great. Thanks!

Does anyone have a list or knows of local junkyards in the riverside/san diego county? Any help would be greatly appreciated. Thanks

Tie rod end on rustys track bar broke. Well actually just the bolt. What can I use to replace it?

Has anyone done this? If so, is it safe? Durable? How long does it last? Answers to any of these questions would be great. Thanks

So i'm just getting around to replacing the tranny mount and I'm having some trouble with it. I started taking the bolts holding the crossmember to the frame and could only get the right side off. The left bolts are spinning but not coming off. Any one know of why it's doing this. Any help at...

Tonight I was driving home after a little wheelin', everything was fine until my entire jeep started shaking and vibrating immensely to the point where I had to go about 5mph for it to be some what tolerable. I finally made it home and got under the rig nothing seemed out of place until I moved...

I have a smittybilt xrc-8 winch and would like to hardwire it with a switch inside the cab. Has anyone done this and can offer some assistance? Any help at all is greatly appreciated. Thanks

I need to know the name of the cone shaped part that connects the transmission to the rear drive shaft. I have an '89 4.0L I-6, with MT. Any help at all would be greatly appreciated! Thanks!

Hey guys, Need some help taking my u-joint out of my driveshaft. I've done close to everything trying to take it out. - as seen here http://www.cherokeeforum.com/showthread.php?t=10072 Thought I'd stop by and ask for a helping hand in the temecula-murrieta area of SoCal. Any help at all would be...