Search results

I'm getting ready to install some new tires on my beadlocks. I installed these tires about 3.5 years ago, and never had any issues or need to take them apart. Being this will be the first time, is it recommended to replace the ring bolts, or can I reuse the old ones. The wheels are ATX Pro...

Pulled together a last minute run tomorrow. A couple of coworkers and myself are meeting at the diamond shamrock in lyons on 66 at 9a in the morning if anyone would like to join.

Anyone interested in a snow run on Yankee Hill or Rollinsville pass? I don't know how much snow either has, but would assume Yankee should have a decent amount.

95 XJ - $6500 obo 133,xxx mi Drivetrain: · Front: D30, Yukon 4.88s, ARB, Yukon 4340 alloy shafts · Rear: Toyota 8.4, Yukon 4.88s, ARB, anti-wrap perches · AX-15 w/ Luk pro gold clutch · NV241OR transfer case (Dakota digital for speed calibration)...

Just a little on what I've been up to. Picked up a new '12 STI. Going to get some seat time in it before I decide what mods I'll be doing. Now I have a toy for the street. :firedevil

As long as it it still open, anyone interested? Tentatively would meet at Ted's place at 9am.

I need a rear windshield wiper arm and washer pump for a 95. thanks

So, I've been pretty busy lately with a new job, but mainly because of getting ready for this little guy. Meet Jayce...

the good: np 231 with 118k on the clock, w/ about 25k on the hd sye tom woods ds is 35" the bad: tc needs to be split, cleaned up, and re-sealed ds could use some new u-joints $375 obo

I had to get a jump to get home from the fair last night, and made it home just fine. I turned the jeep off, and back to the solenoid clicking. So, my problem is my wife is out of town with the other vehicle, which leaves me with no transportation or a way to jump start the jeep. I'd like to...

231 w/ AA sye out of my '95 23 spline input 118k total on the case and about 25k on the sye It does have a leak, but I think the case just needs to be split, cleaned up, and re-sealed. Tom Woods Driveshaft 35" At a minimum the axle end u-joint needs replaced, maybe total rebuild. $450 for all

Does anyone have or know of any job leads for an electrical engineer? The past five years I've worked with a manufacturer doing everything from inside sales, product development, and programming to on-site commissioning. Previous to that I worked in the controls industry. I'm looking to get...

http://naxja.org/forum/showthread.php?t=1031911 $100 you pay for shipping

I have (2) 8" 5150s, and they are in great shape. Willing to ship on your dime. Specs are below. $100 BF5-A195-H1 8.33 5150 Crossflow 255/70 Attached 22.50 14.17 14mm eye/eye

good or bad idea? When I swapped in a 241, one of the case bolts is resting on the plate above the rubber mount to the crossmember. Also, everything seems to be pushed up about a 1/2" or so. So, would there be any negative effects of cutting out a rectangle for the tc bolt to set inside, and...

'95, 4.0, ax-15 When doing my tc swap this past week I noticed a pair of wires that either were cut, or I snapped them when lowering the tranny. One is orange and the other is black. They're about a 22 ga wire. I can't tell where they come from or where they go, but they go up underneath the...

Anyone available to help install a 241 on April 2nd? I'm just east of Ft. Collins. Thanks

Looking for a good tent site. Here's the list my wife and I have narrowed it to. In no particular order: canyonlands moab valley arch view slickrock Thoughts on which are better. Main requirement from wife is a pool for her and the kid. Most recently we stayed at Canyonlands, but in a cabin...

I'm looking for both the 4wd light plug and the speedo plug. I want to use them on the 241 I bought.

Were the high altitude cps units only for certain years? The dealer ship didn't have an alternate part for my 95. Mine took a dump this morning. The last time I bought one from vatozone for around $50 it seems, but now vatozone/advanced auto want about $80, the dealership wants $127, and...