Search results

Just replaced both 02 senors not 2 days ago, now my light is back on and it is reading high voltage to the 02 senors. it runs fine on the highway but when you stop at a red light it will start missing and stalling. I have done some searching, what i need to know is, what will cause the high...

I have a 2000 XJ. The Wires on the sensor got ripped in half by the drive shaft yoke. there is a black, gray, and 2 white wires. What are the white wires, and will it hurt if they are backwards. I have reatatched them but i am not sure they are correct. thanks for any input. Heath

anyone know where to get the plastic connector where the trans lines go in to the tranny???? later Heath

what is the best way to get the inner c to break loose from the tubes. I have cut the weld s with a cut off wheel but the knuckle still does not want to budge. any suggestions??? later Heath

I just got a 91 high output 4.0 aw4 4X4, what is the trans switch on the dash. is this an over drive or for manual shifting. later heath

First, I have searched! I have an 88 with 6.5 inches of lift, 33/12.50/15 Maxxis bighorns. I have already converted the steering got the draglink and track bar angles correct. after hitting a bump the jeep will start to wobble mainly at lower speeds say about 30/40. running down the...

i have a 2000 xj, there is an 02 sensor behind the CC, can I take the CC out and it not harm the o2 reading??????? later Heath

My rig has about 6.5in of lift cross over steering with raised track bar mount and a drop pitman arm. Caster is set at stock spec. when i had it alighned the shop said that my inner knockles were bent and that is why the tires are wearing so bad. anyway have any of you had this prob, and is...

My Controls are screwed if I have the switch set on the dashvents at idle it works fine but if I start to accelerate the air goes to the defrost vents and stays that way until I let of off the gas. anyone have any ideas?????

After cutting and welding on the coil spring mount and the old track bar mount. I installed a otk steering set up that I have made myself, now the font axle is not ingaugeing. I never actully welded on the axle housing itself just the coil bucket and part of the old trackbr mount. Any...

I have just came across a set of d 44s out of a grand waggonier. I have just gotten the motor back in my Jeep and also lifted it 6.5 inches( with adjustible upper and lower arms. Now that I have the 44s I want to go ahead and make a set of long arms while making the swap, also planning on doing...

I have Just dropped the motor back in my Jeep, It is an 88 and I was wondering if you can swap to a later model radiator with a radiator cap, instead of the burp bottle. Hope to get some pics up before to long, so far I have 6.5" of home grown lift 33s and just rebuilt the motor. Later Heath...

I have a d30 under the front of my XJ, I have just put 6.5 coils and new lower control arms under it ( the uppers are still in the process, What cautions do I need to take while cutting or welding on the axle??? I am going to do an over the axle trackbar mount and a custom over OTK stering set...

Have any other folks tried using 3/4 ton leafs from a 78/ 79 4x4 dodge truck. I have a dana 60 with 4/10 gears and a really good set of springs. the springs measure out to fit and looks like it will give an extra 5 to 6 inches of lift. Just wondering if anyone else has done this?? Later Heath

I am currently building an 88 Renix 4.0 . I was going to try and put an after market cam in ( small RV cam ) but after looking at it how do you set the timeing the Distubuter can not be advanced to make up the diffrence in the cam. What modifications have to be done in order to put an after...

Does anyone know where to find 4.0L crate, or long block engines? Also where are good sources for master rebuild kits. I need to try and get a little bit more out of my 88 maybe a small cam and header. I am looking for any advice I can get. this ride will be my daily driver as well as a tripper...

I have found a 93 recked xj. I have an 88 that is in great condition other than the motor and tranny. I would like to have the power of the high output from the 93. My motor needs to be completly rebuilt or a long block dropped back in. What would be the advantages of stripping the 93 and...

What type of problems will I run into on this swap. Will I have to change the input shaft of my t case, or willl I have to ghange Tcase all together. I belive it is an NP231 but not sure. How can I tell for sure what it is, where are the ## or vin plate on the T Case, axles, and tranny...

I have an 88 xj with the 4.0, it is blowing oil out of just about every seal possible and starting to loose power. The motor still runs extremely well, no knocks or rattles, and still gets really good gas mileage. I am looking for any advise on where to get the best master rebuild kit for it...