Search results

Sorry to re-open this thread...but...Hasta What's best for our outings, FRS, GMRS hand held HAM's? Before I buy something that nobody else is using, I figure I should ask first and spend later.:helpme::D

So, just curious. What's the common radio used now? I still have your average, everyday CB radio. If I remember right, about the only person I could talk to last time I was out there (2019) was Eric. So, I guess I better upgrade my radio options before I attend this year. Thanks.

I have a set of 5 Raceline 928M wheels, 17x9 with -12mm offset (4.5" back spacing) and 5x5.5" lug pattern I'm looking to sell. 4 of them have some minor rock rash on the "locking" ring, but nothing too serious. These are fake beadlocks, not the real thing. But they are pretty tough and the bolts...

For the d60 I just finished, and the d44 that it replaced, I just used the axle flanges at the end of the tubes to measure to the spring pads, after I figured out the center-to-center for the spring pads first. Also, some people recommend to have the yoke slightly down, 1 or 2 degrees, from a...

I had a similar setup on mine for quite awhile. If there was any bump steer, it was't really noticeable. Even the larger dips in the freeways that caused the suspension to cycle more than normal didn't cause me any issues. My axle was narrowed about 2 inches and I'm still using my old...

I love the pic of your thumb.:D I should have gotten a pic of my hand a couple months ago. 3 pound sledge to the side of my index while driving my d60 axle tube onto the inner sleeve I used for narrowing the axle. Turned my entire hand funny colors and the entire palm, index and middle finger...

That's great. Thanks for all the hard work.

Return PM sent Eric.

Dang it all! I forgot to do this in time. Sorry Sierra Chapter.

I almost forgot, for the future items, is a set of 5 17x8.5 Raceline 928M wheels with 5x5.5" pattern. These are the street version of their beadlocks. 4 of the 5 has a little rock rash on the "locking" ring. The 5th was the spare the last time I ran a trail. I'll probably be asking about $500...

I've got a few things I would like to get out of my garage so I have room to put more junk in there. Here's what I have, that I remember right now. A set of Full Traction 6" front coils - $40 Stock Ford E350 32-spline FF axle shafts in good shape(if I remember right they are 35" & 37.5" in...

I want to go...I'll keep my fingers crossed that I'll be able to go.

I want to go...I'll keep my fingers crossed that I'll be able to go.

Happy New Year everyone!!

Phil, I'll pm you.

I have a '91, gray though instead of chrome.

Costco has a Satellite phone package available. I keep seeing it when I go shopping, but haven't looked too closely. It's something like $250 or $350 (don't remember right now) and comes with pre-paid service. I think it said it does calls and texts, but I'm not 100% sure on that. Anyway, just a...

The way I had it set up was with the GM small spindle and the ford hubs for 5x5.5 lug pattern. It was right around 62" to 63" wms with this set up. I had 1.25" adapters on the rear XJ d44 to match it's width. I'm not sure (you probably know more than I do about this) but you may be able to mount...

I am selling my old d44 front housing. It is a full TnT trussed, F150 housing narrowed to accept TJ Rubicon inner shafts. I am selling the housing, the 4340 inner shafts /Spicer u-joints and a RuffStuff cover. I'm asking $400. I can include a set of GM knuckles that need cleaned and ball joints...

I don't think I'll be making it this year. I have my new front axle in, with lower gears, but still have the 4.88's in the rear. The problem is, the car I was driving daily so I could get the gears done decided it wanted to go off on it's own without asking for my permission or anything. It has...