Search results

So I've fixed my recurring no-charge with a new alternator and external regulator. In addition, I have house batteries on an isolator (diode). The voltage drop across the isolator is about 1v -1.5v give or take. The question is, since the external voltage regulator is set to say, 14.5v in...

I’ve been having a no charge issue for some time now, I got the alternator replaced with a Powermaster factory refurb, and added an external voltage regulator, reworked some grounds, including adding an alternator to engine block ground. I’ve got the ignition source wire to the external...

https://www.popvox.com/us/federal/bills/115/hr6502 H.R. 6502, the Reducing Unnecessary Senior Hospitalizations Act of 2018 or the RUSH Act of 2018, is an extremely important bill in my industry that is currently under consideration. The link above provides a form letter and a means of...

Should they both be 12v+? Is one low voltage or ground? 2001 XJ I'm putting out 4v from the alternator at idle, which is killing the battery. Thanks

Soooooo...after not running for a year, a new fuel pump, a new camshaft sensor, new gas and a lot of cursing, the 2001 is running, such as it is. I immediately topped off the oil once it started, oil pressure/levelseems fine, but it's got a tick, round about the 3/4 cylinder, most pronounced on...

Ugh, so the 2001 came off the road for a while as it got retired from DD. The gas in the tank turned and I didn't start it for a year because of that. I dropped the tank and noticed a mouse nest around the fuel pump. They started to eat the insulation, I rewrapped everything there. Poured out...

Anyone see these for sale new anywhere? Black mesh stone guards as well, and/or just the mounting hardware? Lost on my restore....

Can a mod help me edit some old and archived posts? Thanks.

Pay shipping or free local pickup 11030. I think I have all 4 control arms. Off of a 2001. Been sitting outside. Also, I have the rear housing cover off of a NP231. Free. OBO. :compwork:

Stock wheels taking up space. Two have been in bags, the other two have MTRs mounted to them with maybe 60% tread. The fifth wheel has a 100% tread MTR mounted to it. Tire size is LT235/75 R15...they are about 4 years old at this point, not sure if they hold air. The spare doesn't have a cap...

I can extend and retract with the remote but the stalk won't swing to free spool from gears engaged.

So, I was working on a Saturn sedan this week and when I put on new wiper blades and dropped the first one onto the windshield the glass on the inside shattered in the center of the wiper...the car has been sitting in one spot in a driveway, exposed, not moving for about 6 years. Surprised the...

I'm digging into a 96 Saturn SL2 that has been sitting for a few years. I'm not sure of the last time it got gas or was run...maybe a year? two? The belts and hoses look good, no interior damage, oil is still liquid. My plan is to suck out as much gas as I can, change the plugs, new battery...

Found this gem on another forum...I think the solution should start with some rigorous road testing, just to pin down the source of the problem....what do you think? All bleeding stops eventually, right?

Pressure problem to the rear...possibly all around. -Vanco up front. -SSBC disks in back. -New soft lines, no leaks. -System bled pedal feels hard with prop valve adjusted to about ~60/40. -Stock prop valve has stem and cap only. (washer on the stem blocks all rear flow and was removed.)...

The XJ as I know it died today, a short and some unforeseeable electrical circumstances involving dash components caused some expensive problems and I need reliable transportation in a bad way to get back to school tomorrow. I bought a Land Rover LR2. I drove the Grand Cherokee Overland but...

Placed order: 9/10/10 12:44PM Had an issue with the NAXJA discount code, didn't apply for some reason...probably my fault, reset the page or entered it incorrectly...anyway: Order confirmation received 9/10/10 10:13PM. Noted that the discount wasn't applied to the order... From...

I have no desire to go changing the unit bearings...I have the Vanco brakes and knuckles up front...I can't do the gears and carrier on my own and I don't want some shop trying to get the rotors to fit, anyway, a 27 spline kit would be easy, but if I'm going there I might as well spring for the...

Is this really mod tech...anyway...I got a couple of these after doing a 110' straight pull for a Liberty driver that got a little too ambitious...otherwise the cable has seen only minimal use in ~3 years...I don't really have the $$ to replace it now, but if its a safety issue I shall go...

Can someone remind me how to read this device? which side of the triangle is the right side to read?