• Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.

Search results

  1. C

    steel shims needed, 7* or so

    The shims I have are not working, so I need new ones. Anyone have any?
  2. C

    WTB: Sway bar discos needed

    I need a set of sway bar disconnects for 3-4" of lift on my XJ. Or a set of mounts for the discos on the swaybars. I had parts assembled to build a set but have managed to loose all the mounting hardware.
  3. C

    93 XJ for parts

    93 XJ for parts it was wrecked and is being stripped and recycled. No engine parts are usable. Neither is the trans or transfer case, rear drive shaft. PM me or call my brother (its his), Joel 717-629-7917. Its located in Ephrata, PA 17522. It should be leaving on Tuesday, if you want something...
  4. C

    WTB Upper Control Arms

    I need a set of UCA's for an XJ with 6" of lift. As long as the measurement is more then 15.25" eye to eye. Adjustable or fixed both work for me.
  5. C

    added shims now VERY BAD vibrations

    After my SYE I had some noticable vibrations at highway speeds which I have blamed on the rear pinon angle being off. I researched and found the recomended difference to be 3* lower at the pinon vs the driveshaft. Mine required a 4* decrease in angle. I added the shims today, RE 4*, and now...
  6. C

    Gas tank skid options

    ok so I am in the search for a gas tank skid for my 01. I would love to find a used one fatory or another but that is very hard to do. So I am looking at Skid row but I do not really like the mounting points but a lot of people swear by them. So what else is there? What are you running?
  7. C

    skid plate question

    Last night we installed the skid row engine/trans skid on my 01 and noticed some contact vibrations and adjusted the mount on the driver side which was found to be making contact with the exhaust. No more issues. Today while driving I am getting intermitant contact with something, I think...
  8. C

    Transfer case help 01XJ

    OK 231 xfer case and I am in the middle of screwing up the SYE instal. Swaping to a cut down shaft and I cannot find the part # or a parts store that carries the part. I am looking for the Rear Output Shaft Seal or Rear Retainer Seal depending on where you look. I have tried both the local...
  9. C

    Tomken tranfercase skid

    ok, I bought a used skid and it didn't come with the "y" mounting piece. Where does this mount? I tried to contact Tomken but did not get anything back in response. If someone would have better pics then listed on their website as well so I can fab a mount. thanks
  10. C

    Powered driver seat from 89 XJ

    I am tired of tripping over this and want it gone. The frame broke and was cobbled back together. Leather seat back and head rest but no bottom. The motors work fine as do the switches which is why I never chucked it. Sold the Jeep to my brother and he doesn't want it. Come get it in Ephrata 17522.
  11. C

    ZJ Lund Visor

    I bought this and then found out that it is for a ZJ and not an XJ. The previous own had never mounted it so he didn't know. It may have been mounted at one time but I doubt it, it has been primer black but could use another coat as it is starting to wear from being stored. I do not have the...
  12. C

    Paragon AP or Cargo Airport vote now

    Ok here is a pole from the local paper covering the possible closure of PAP. They are holding a public pole at the bottom of their home page. http://www.standardspeaker.com/
  13. C

    LCA and UCA ??'s

    Ok so this is a very newb question but I just don't have the answer. If I replace the LCA's with a longer CA's do I need to replace the uppers as well? I would think yes but I can't seem to find the answer. Maybe I haven't searched well enough.
Back
Top