Search results

One set of X-297 disconnect-style axle shafts, both sides, inners/joints/outers. These axles will fit any YJ or any XJ with the vacuum disconnect front axle. These shafts are from a stock YJ that has never been off road. $175+shipping for everything.

I'm looking for a '97 or newer XJ somewhere within a couple hours of Nashville. I mainly want it for commuting but I'm sure it will eventually turn into a trial vehicle so I don't want anything too nice. I prefer an SE or a sport model. A/C, 4wd, and four doors are a must. High miles not a...

I got back from Tellico last night, there has been alot of trail work done since I was last there (it's been a while). The approach to Guardrail has been filled, no more ruts. Getting to Gaurdrail is a breeze now. Helicopter Pad and Schoolbus looked about the same as did upper 2. Lower 2 has had...

These are custom machined 3 degree shims with an offset center pin that is relocated 5/8” towards the thick side of the shim (moves the rear axle back). Just to clear up any confusion, the hole for the leaf spring pin is centered in the top of the block but the pin that locates into the axle...

I hope noone minds me posting for sale stuff here, I don't want to ship this stuff so I figured this was the best way to reach potential buyers in my area. Okay, here goes: -Drawtite adjustable tow bar. Only used once. Comes with safety chains, bumper brackets not included (easy to fab or cheap...

I have a front output bearing going south so I'm going to rebuild the 231 this weekend. I've got the complete rebuild kit on the way along with a new chain so I should have all I need to make it good as new. Is there anything I should look out for when rebuilding it? I've done several SYE's so...

The last few trails ride I've run I have been having a strange problem. When the engine bay is good and hot, engine not overheating though, and I kill the engine it won't start right back up. It will turn over but won't fire. It gets fuel, not sure about spark. Let it sit with the hood open 5-10...

I've tried researching but I've found anwers from just remove, replace, reassemble all the way to tear down the entire axle to accurately check bearing preload. What's the real deal? I've bought new pinion seals and pinion nuts. Now how do I replace the seals without messing anything up?

Basics: 1993 Jeep Cherokee sport, dark green, 5-speed, cold AC, power windows and locks, cruise, cloth seats. Front axle: High pinion Dana 30, 4.56 Spicer gears, Detroit locker, ’00 TJ axle shafts with X-760 joints spot welded in place. Lower control arm mounts have been boxed with 1/8” steel...

What are you guys with tweaked wheelbases and/or modified suspensions using for bumpstops? I'm going through shocks too often using them as bumpstops so I need to get a real solution figured out. I tore my front end down this weekend and while I was at it I cycled the suspension trying to figure...

Greg, Check your PM.

I knocked the corner of one of the "wings" over the right tail light off somewhere in Tellico last weekend. I would like to cover it up with some type of protection/plating but I'm thinking the compound bends might be next to impossible. Anyone fab up thier own protection or cover panels? I...

Now that the Crawl is over hopefully there is some interest in riding more often. How about getting together for some riding in Monteagle? We could make it a weekend since it's a long drive for some. Meet up and ride Saturday, camp/motel that night and ride again Sunday. Who's in? How about the...

It's Saturday night and I just got back into town. I decided to skip out early and get a jump on the rest of my vacation, I hate I missed the meal though. I figured running Slickrock and Lower 2 in two days with all that rain without any serious damage was enough fun for one weekend. Once again...

My tenative plan is to ride with the moderate group on Thrudsday and branch off onto Slickrock at some point to get my feet wet. If the weather gods smile on us and the trial isn't too washed out I would like to hit Lower 2 early Friday morning. Anyone else game? My ERoCC partner will be there...

I have some parts taking up space that I would like to get rid of. 1. Stock rear driveshaft, no u-joints, no slip yoke. 2. Swaybar disconnects that will work up to ~4" of lift. 3. Stock swaybar. If anyone wants them I will bring them and they are yours.

A group of us will be there if anyone wants to meet up and putt around.

I need a battery tray in good condition that will fit a '93 XJ. If you have one let me know what you want for it. Wes

I finally got around to getting the pictures up from the first ERoCC. We rolled twice yet still managed to finish in the middle of the pack. It was a great time though, I can't wait until the June event. Pictures are here.

Anyone interested in riding that weekend? I'll definitely be there, not sure what the ride will be like though. I guess it will all depend on who shows up and what you want to ride.