Search results

how difficult is it to remove the AC system, then wire the electric fan to a switch? Does anyone have a writeup on this? What belt should I get if I remove the compressor? thanks

can anyone tell me how far off my speedo would be after changing from 3.55 to 4.56 gears? I have 31's on, and put a new speedogear in to correct for that. I know I need a new speedo gear to correct(anyone know a good place to get them besides the stealership?), but would like to at least have...

booster cables Not really a modified tech question, but where is a good source for high quality jumper cables? looking for long term durability and flexible cables.

does anyone have pics of the driveshaft side of a d30 low pinion and a d30 high pinion? Are the gear sets and install kits the same for both?

who makes motive gears? is it a lower end brand from one of the larger manufacturers? is the quality good on these?

what is the best/least expensive place to get quality gear sets for my d30 and chryco 8.25? also, anyone use richmond gears?

Seen a few questions about this bumper. Finally got mine installed. hardest part was the fender trimming. still need to get some bolts to mount my lights, but the rest is done. It's really beefy, and the d-ring tabs and the receiver go all the way through the tubing that provides the...

I've got a 3500 pound rear hitch with the factory nut strips and a tow bar. Excellent condition and doesn't even need a repaint. $50 plus shipping from 59632.

finally decided on the currie drag link and a rusty's tie rod. got the drag link from red rock 4x4, and Jason there was super helpful, and way cool to deal with. I am impressed with the drag link as it is way beefy. after install and alignment(thanks GoJeep-your website rocks) I am very...

Need to replace my steering setup, and don't want to do the 1 ton conversion(overkill for me, and I don't want to ream the knuckles). I'd like some opinions on the subject. I've narrowed to 2 options: Rustys heavy tie rod w/ends, A heavy duty WJ Drag link from Kevins, and a new TRE for the...

Is there a heavier duty TRE that can be used in place of the stock TRE's on the jeep without reaming the knuckles? Looking to upgrade the steering to a full tie rod setup like the 1-ton setups, but don't want to ream the knuckles. Are there any options? thanks

This question is for you guys with the detours rear bumper: Has anyone had any problems with rust under the quarter guards? Whats a good way to prevent rust when I install the one I have in the garage? thanks

It's a long story, but due to UPS screw up's, personal impatience, and Ebay, I ended up with 2 of these, so one's got to go. Check out the specs here: http://www.garmin.com/products/etrexVistacx/ This is the best GPS I've ever used. real topo maps downloadable, compass, altimeter, color...

do I need the nut plate for both sides to install a hitch? I searched and it seems that there should be one on the right side already for the exhaust hanger, but my hanger doesn't bolt through the holes that the hitch uses. it has 2 small bolts side by side. also, what is the bolt size and...

wil a 27 spline 8.25 hold up to 33's and a detroit locker on mild to moderate wheeling?

Is there a detroit truetrac available for the 27 spline(96 and older) 8.25 axle? and Does anyone know the mopar performance part # for the 27 spline detroit locker?

bumper?

does anyone have pics ofthe durango blade bumper mounted on their rigs? thanks

anyone know of anyone making a bumper similar to the ARB winch bumper, but without the winch part? looking for that style, but want to put reciever in the bumper and keep the winch in a cradle, so I don't need one with the winch tray.

went out ot my jeep today('95 sport) and the power locks won't work. the relays click, but none of the locks work. any thoughts?