Search results

Come pick them up, or I am going to scrap them... in February before I move. Both come out of a 99 XJ, and had less than 40k miles on them. Novi, Michigan 25 mintues north west of Detroit

$50 obo for the set and they are yours if you pick them up from my house in Novi, MI. Shipping probably makes them not worth it.

One tire has a leak which may be able to be repaired. I have the center cap which is not shown in the picture if you want it. Some chunks out of the sidewalls, and probably half the tread is left. Wheels have hit rocks several times. I will include an additional stock spare steel wheel and...

Set of 5 - 33"x12.5" BFG Mud Terrain tires on 15" x 8" Steel Wheels One tire has a puncture in the sidewall that was trail repaired only semi successfully (slow leak). Good amount of tread left, driven on road about 1000 miles, and wheeled 3 weekends. Some sidewall chunks. One tire is an older...

5 Stock Wheels and tires 4 with >1/4" tread, 1 never used 99 spare - $100 obo 1999 Steering Gear (replaced but wasn't the problem)- $50 1999 8.25 Axle Housing - Take it away 2001 Dana 30 LP Axle Housing and ends - take it away 1999 Stock rear driveshaft (Manual to 8.25) - take it...

Some of my friends that I normally go wheeling with want to get out to Paragon on the weekend of June30 to July 2nd. I will be in New York visiting my parents and will not have my jeep. Would anyone want to go along with them since they are only 2 vehicles? I would be there on Sunday...

Yeah... even though I have been there like 4-5 times.... What is the Exit off of 81? I will probably know it from there, with all of those Blue tent signs everywhere... I remember an old thread with nice directions that describe every turn which would be nice for anyone travelling there for...

Pictures are up on www.blank-page.org. enjoy

I just was replacing my axle end seal in my 8.25 and when I put the locker back together it would not pass the test as describe in the manual. Rolling the driver side wheel forward and then holding it in position the pass wheel would not disengage in EITHER direction. My next set of tests...

Anyone know what is going on with Michigan Jeepers? just curious since it came up the other day as an unregisted domain, and today something about an upgrade...

PM Me withe the email address to send it to if anyone wants these.... just be sure to accept the invites so I can get more... You all probably know what this is, but if not, it is Google's email service that gives you 1GB of email storage and is super user friendly.. but still in beta...

Anyone know the difference between these two, I just got parts from a local driveshaft shop, and they gave me 3 153 joints instead of what the catalog says that the two in the CV joint are supposed to be 278 joints.. they look the same... did this guy screw me, or can I use the 153s in place of...

What is going on here? why does the cross pin not fit?? these are Precision Gears, and the carrier came from my stock 3.07 gears in my 29 spline 8.25 from my 99XJ? Other research I did said there is no break for carriers for 8.25... wtf?

Will an MJ transfercase crossmember work on and XJ and is it an upgrade? I have read that there are more attachment points, but do the 4 XJ ones work? Thanks.

Sylvania Xenarc X6054 HID Xenon upgrade complete kit brand new. All parts are included which are required to upgrade your XJ to HID. Includes complete lamps, with bulbs and ballasts and all wiring. $200 shipped to anywhere in lower 48 these retail anywhere from $300 to $800

I have noticed lately that my clutch is slipping when i try to park on any bit of a hill. SO, the only brand name I have seen is centerforce. BUT I have also read that there is not much of a slippage zone on those. So, what else is there, or should I just throw in a crappy clutch, and just...

I put up a bunch of pictures on my website www.blank-page.org. I have a couple of videos I took with the camera as well, and will get those up as soon as I can.

What is the best way to get there from I-75 coming south? Mapblast says to go down to cleveland. Is that the best way, or is there a better way to get off in Knoxville? A bit late since I am leaving tomorrow... but thanks for any help.

I have definately decided on either a Millermatic 175 -or- Hobart Handler 180 based on many good suggestions around the board. apparently the only reason to go to the Millermatic for 100 bucks more is infinite adjustment on the current. Now for a autodarkening helmet. On EBAY I see...

I have a front drive shaft that I just bought at the junkyard for a spare it is out of a 98, but an automatic, so I cant use it on my manual, it is about 1.5" too long. If anyone can use this for a spare, I paid $100 for it, and am offering it up before I try to return it to the junkyard....