Search results

91, 4.0 A little backstory, I had pulled the jeep out to clean the garage the other day, meant to put it back in but never got to it, hood is off and it rained last night. Went out to go start it this morning and the battery is dead. Dead dead. So I think well that's wierd and hook up the...

91 4.0 So my browndog motor mounts came in today and I'm planning on installing them tomorrow. Any tips to make it easier? Thanks, Dustin

91, 4.0. I'm going to do the Thermostat and housing tomorrow and the lower bolt seems exceedingly difficult to get to with the belt tensioned, I looked but couldn't seem to find the tensioner can anyone point me to it? Thanks for helping a dummy.

Would taking off the trackbar mess with my alignment? I don't think it would but thought I would ask those more knowledgable than I. Thanks.

Is there any way to change a threads name? IF not it's cool I can just start another thread for my build follow, but I'd rather just change the thread name for the one I already have going.

I have two issues, 1. My fuel tank is all bashed to heck from wheeling without a skid so it needs to be replaced and 2. I would like to have an extra source of fuel for those long, out of the way trips. What do you all suggest for extra fuel and does anyone know where to get a stock (Or bigger...

Anyone ever use offroadlockers.com ? Thoughts, opinions, complaints? Thanks!

Well after my XJ sitting for close to 2 years, my buddies have PESTERED me enough to try and get it worthy for Moab here in May. It starts and runs but is definitely in need of some TLC . (Oil change, tune up, motor mounts, alternator, hoses...) I started building this truck right out of high...

I'm a total dunce when it comes to this stuff, the light has three wires, and they are labeled, GROUND, TAIL, and STOP&TURN. Now you'd think I'd be able to figure it out but I can't. I can wire it so I have my tail lights. I can wire it so I have turn signals. I can wire it so I have Brake...

3" rough country, 2" shackles and coil spacers, 33" somethinsomethin AT's I got for free from the owner of the flatty... Never ending project... Workin on priming it, the paints pretty shot...

I have this HORRIBLE vibration sometimes when shifting from first gear to second or second to third. It only happens when letting the clutch out, once the clutch is out no vibration. It did it in reverse twice today too... Never starting out in first though, only starting in second or shifting...

How do I go about removing the crankshaft pulley without the motor turning? I try to loosen the nut but it just turns the motor... TIA :repair:

I went out wheelin this weekend and my jeep started overheating and not charging the battery out of the blue. so we strapped it back home and i got to looking into the problem and it appears as though the crank pulley is not turning the belt thereby causing the water pump not to turn and the...

Don't know if this is the right spot for this but oh well... I was just wondering if anyone had a poor mans locker (welded diff) in the front, if so how does it work out for you and how long till I break somthing if i do it? Also I was wondering whats the biggest tire I can run on 3" of lift?

I don't know if this is the right section for this, if not one of the mods can move it. I wondering if it would be better to get ANOTHER rebuilt 4.0 or just break down and buy a new 4.0. I am on my second rebuilt right now and it's starting to take a dump on me (just like the last one)...

how hard is it to replace the front axle shafts? can a DIY'er do it easily? about how long will it take? I want to get on the trail by this weekend...

Ok I have a '91 XJ 4.0 HO that is stock, but is going to be going under construction in the next few weeks. A few weeks ago I went out wheeling with my buddies and my four wheel drive would not engage, not a big deal just couldn't really do any of the fun stuff with them. Got back into town and...