Search results

Does anybody in Junction City, Fort Riley, or Manhattan Kansas have a pair of stock XJ leaf spring packs they'll give away or sell cheap? I haven't found a good junkyard here yet.

Hey guys, This is the 4th or 5th gear setup I've done, but it's been a couple years. Can you guys take a look and tell me how the pattern looks? It's a used 4.10 gearset, so what I've read is that the coast pattern is more important than the drive-side pattern on used gears. It looks alright...

So after all my work converting an '88 2.5 to MPI, electric fan, etc. to give it more power, it just isn't enough after my ax-15 install, 4x4 conversion, 8.8 rear, etc. I've been thinking about different engine swaps that would make it nicer to drive. I've ruled out the 4.0 simply because IMO...

1993 Jeep Cherokee Sport I'm the 2nd owner. First owner was an older lady that put 80,000 miles on it and never even put it into 4wd. I have driven it more aggressively than that for the last 62,000 miles but it has been well maintained. 2-Door Full-time 4x4 (NP242 Transfer Case) 4.0L Straight...

1993 Jeep Cherokee Sport I'm the 2nd owner. First owner was an older lady that put 80,000 miles on it and never even put it into 4wd. I have driven it more aggressively than that for the last 62,000 miles but it has been well maintained. 2-Door Full-time 4x4 (NP242 Transfer Case) 4.0L Straight...

I'm going to build a lightweight trailer, ~1000 lbs capacity, just enough to haul my front D60 from Utah to AZ. Needs to be lightweight so the minivan can tow it (the family won't fit in the MJ for the trip), and super cheap (less than $275 total). Trailer axles aren't all that cheap, but I...

I'm looking for a light duty axle to use on a light-duty trailer and just need the cheapest thing I can find. I'll give somebody $10 for an old D35 they've pulled that's still sitting around your yard if it's in Prescott, PV, Chino, or Dewey. I had one I pulled out of my MJ but somebody stole...

External Slave Cylinder Bellhousing for an AX-15 transmission. Came out of a '98 XJ (5-speed, 4x4, 4.0L) with 98,000 miles. If you have a '93 or earlier XJ with the AX-15, this can be used to convert your setup to an external slave, which will allow you to easily swap out the slave cylinder when...

'87 XJ Dana 44 Rear Axle Trussed Top & Bottom (the bridges over & under the diff were professionally welded to the diff, the whole thing was professionally jigged prior to welding to make sure the axle was straight as well). Bottom truss is minimal and does not affect ground clearance at all...

Anybody know how to remove the gear shifter (the long lever) from the shift tower? It looks like there are spring-loaded balls possibly that once in place would require some special tool to remove. This is from my AX-4 to AX-15 swap. The tranny is in, but the junkyard tranny I got just came...

I stripped down a Ford 8.8 axle. Here is what's available: Axle Shafts $50 (28 spline, not 31) 4.10 Ring & Pinion Gears $35 Limited Slip Carrier $35 (28 spline) Companion Flange $20 I'm willing to ship to the lower 48, but shipping is not included in the prices. I'll charge actual shipping via...

C-Rok rear bumper Awesome departure angle, made from 3/16" steel. Awesome bumper. Would keep it if I was keeping the XJ. Needs to be cleaned up and re-painted. $375 Located in AZ 86314. [email protected] http://www.c-rok.com/Rearbumper.html

Stock track bar with the tie-rod end cut off and a small RE joint welded on. Extra length added to make it the proper length for a 2"-3.5" lift. It is not adjustable. Comes with the RE1665 bracket. Click the thumbnail below for pics. $150 + shipping. Located in AZ 86314. I have a TNT...

PARTS OFF OF AN '05 WRANGLER UNLIMITED RUBICON (LJ). All parts were removed at 22,000 miles. Stock Front & Rear Flares, in perfect condition $75 LJ Rubicon Rocker Guards (diamond plate, black). They've never seen a rock. $75 LJ Rubicon Front Springs $50 (gives about an inch lift over stock...

'87 XJ Dana 44 Rear Axle Trussed Top & Bottom (the bridge over the diff was professionally welded to the diff, the whole thing was professionally jigged prior to welding to make sure the axle was straight as well). Bottom truss is minimal and does not affect ground clearance at all Bottom of...

Custom front bumper (non-winch) Cut & formed from 1/4" box steel Mounting setup made from 3/16" steel and goes way back on the frame sides(basically a copy of the c-rok plates, both left & right sides) additional bracing for the mounting strengthens the front crossmember and ties into the bumper...

Detroit Soft Locker for 27-spline Dana 30 works perfectly, good condition It has never had a problem, but I'm moving to a bigger front axle. $375 My email is [email protected]

Dana 30 front axle for an XJ/MJ/TJ/ZJ. Came out of a '93 XJ 4.88 Yukon gears installed open diff This would be perfect for somebody looking for a cheap way to get deeper gears. missing driver-side axle shaft (you can easily put the shaft from your current rig in) comes with the unit bearings...

I'll be running several Moab trails Wed 6/17 through Mon 6/22. I'll be doing a lot of the harder trails. If anybody wants to go, just let me know.

My temp gauge stopped working a while ago. I have replaced the sensor at the back of the head, checked all of the fuses under the dash & in the engine compartment, and even tried a different temp gauge in the gauge cluster (I have not replaced the entire gauge cluster). Any other ideas of what...