Search results

In all my searching, I haven’t seen a repair for this type of fuel line fitting. I have seen other looking fuel line adaptations but nothing that looks like mine. I assumed I needed to replace the o-rings but how do you get the o-rings out and back into this connector? Can I just buy a new...

Hey guys - My Jeep is a 91 XJ limited with the 4.0. My AC stopped working about 5 years ago and I never fixed it. I get a quote from a shop every year thinking “now is the time” but the $1200 estimate never sits well and another year goes by. My Jeep has transitioned into being my...

Hi guys - my XJ is a 91, and we've had it since it was a year old. The other day I noticed my headliner appeared like it got wet and dried. Does this look like a factory roof rack leak? I also have a sunroof so I'm not sure if it's running from the sunroof down to the grab handle area. This...

Title pretty much says it all. I have a Dana 30 and I'm about to replace the pinion seal. Apart from buying the wrong seal 2x, it seems straightforward. However, this job seems identical to replacing my SYE output seal, and that called for a rubber crush washer and RTV inside the yoke. Is...

Looking for a decent set of 4.5" coil springs. I'm currently running a 3.5" set with an aluminum spacer on top and I swear my front end rattle is coming from those things. Wanna replace with a single coil, no spacer. Thanks! Sent from my iPhone using Tapatalk

(reposting here - I accidentally originally posted in the SEC section) Hi everyone - I recently installed a B.Lee 3-Link in my 91 XJ, and while the axle was out, I swapped in a lower mileage HP Dana 30. Mine had 360k and backlash was way out so since they're plentiful, I just picked another one...

Hi everyone - I recently installed a B.Lee 3-Link in my 91 XJ, and while the axle was out, I swapped in a lower mileage HP Dana 30. Mine had 360k and since they're plentiful, I just picked one up that supposedly had lower mileage. Before installing, I checked backlash and it was in spec. I...

I've read a few threads showing the words "manifold side" on the replacement exhaust manifold gasket, showing a correct installation direction. I'm my case the manifold gasket is a simple stamped piece of gasket material. Like a stamped washer, one side is the "sharp" side, and the other is...

Selling my Moab wheels and tires to fund other things. 16" OEM Jeep Moabs - looking for $525 for the set of 5. Located in Huntersville, NC. Rims are 5x4.5 bolt pattern. Primary 4: wrapped in 285/75-16 Falken A/T's. They have about 6/32 left. Spare: wrapped in a brand new 245/75-16...

Hey guys, name's Greyson. I've been around the forum for a few months now, mostly trying to learn and also asking questions about my Jeep specifically. I contribute where I can. I figured I should start a build thread to consolidate everything and introduce my Jeep. Please follow along - I'm...

I picked up this sweet tire carrier a guy locally had built for his XJ. Guy sold his XJ and kept the bumper to sell separate to optimize cash return for his sale. Long story short, I picked it up for a steal. My concern, however is that this bumper only bolts to the stock 8 bolt holes in...

Hey Guys, I have a 1991 XJ with 3.5" RE lift with full packs. I'm running my stock front driveshaft in the rear with a Crown SYE kit and a chrysler 8.25 swapped in. I also have a 4 degree shim in the back to correct the pinion angle for the double cardon shaft. Interestingly enough, my rear...

1991 XJ 231 T-case 335k miles 4.0 HO engine Crown SYE Currently racking my brain over a speedometer issue. Speedometer/odometer went out a while ago. It "fluttered" for a while and eventually stopped. makes me think it's electrical. The speedo sensor on my T-case outputs to a 2-wire plug...

Hi there, I've read many many threads on this and although it seems that despite this being a common problem and there's ample info, I still can't get my drivers door open consistently on my 91 XJ. At the end of a three hour struggle last night, I actually got the door open. I literally did...

Hi there! First post here. I'll Scott over and find an intro thread and post there too. I'm having an issue I can't diagnose... My Jeep is a 1991 XJ limited with the 4.0 and NP242. I should start by saying I had the transfer case out this weekend (needed to check input shaft length because...