Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
Does anyone know the correct name, and/or, manufacturer part number for the seal (looks like wiper style) between forward edge of each rear door and the body-side pillar?
They're both held on by adhesive, but now mine have ripped and fallen off leaving a gap.
I've turned up other searches...
Hello,
The background...
This past weekend I replaced my cracked head. Because it was off, I went ahead and replaced the exhaust manifold with Doug Thorley Header setup. My pre-cats were also bad, so I bought replacement Catco dual pre-cat setup.
Now the issue...
I doubted the way the...
Hello everyone,
I just installed my lovely temp gauge.
It'd all wired up, but I'm not getting a valid reading. The gauge illumination works, but the needle stays below 100 F.
Either my temps aren't reaching (I doubt it, even though it's 10 F here in Ohio) or the wiring isn't done correctly...
Good evening everyone,
I was curious how one would determine the appropriate impact to your STFT & LTFT based on a new set of injectors you install.
For example, does an injector set that is either 10% lower or 10% higher in fuel flow rating (at same rail pressure of 49psi, 2001 XJ here) mean...
Hi all.
Yes, I picked probably the most widely used subject title for this post.
And yes, I know there is a wide variety of discussion already ongoing about system overheating.
But I think my case may be a bit more unique.
I've had my XJ for almost a year now, and for the most part no...
Has anyone had any luck finding an online site that had replacement bolts which actually fit for FP to TC?
I was looking at
http://m.autozone.com/nuts-bolts-and-washers/torque-converter-bolt/mr-gasket-torque-converter-bolt-for-chrysler/193899_0_0/?location=
I don't want to reuse the ones I...
Hi everyone.
I've recently been running into a pretty irritating issue on my XJ that won't go away. I'm hoping someone has some insight on which direction I should pursue next.
<Symptoms>
1. "tick" at idle
2. hard tapping/vibration under load (1500-2500 rpms), every gear except OD...
Everytime I try to upload my custom avatar (100x70, 12.2KB) it says "invalid file".
Why would this be?
I've tried uploading it under every file extension I can think of (bit, jpeg, png) and using every photo sharing website I can think of too.
Just to make sure photo sharing link works, below...
So I replaced my blower motor today, old one was shot (cage broke, bearing ringing). Shortly after replacing it, I found that only the highest speed setting worked. So, pulled the BMR and replaced with a new one.
I tested it before installing back into the dash, and on the two lowest settings...
Good morning everyone,
I've been having an issue with the truck getting started, and maintaining idle as of recent.
About once or twice a week, I can't start her up. The starter cranks and the engine nearly gets going but then it just dies. I can give it gas, but as soon as I leave off the...
Hello everyone,
I'll be replacing the rear wheel cylinders and replacing seals on the calipers next weekend.
For those of you who have done it, have you simply bled the brake system dry, done your work, then filled back up?
Or have some found a way to plug/cap the lines as you replace a...
Hello NAXJA members
I have a 2001 XJ that I bought back in Nov. Ever since I've bought it, there's been a ringing noise from what I believe might be the braking system.
The best way I can describe it is the sound you get when you wet your finger and rub it around the rim of an empty wine...