Search results

Years ago I used a Gen-Right license plate lamp on my lowered C-10. I loved it cause it was LED, had a light for the plate, stoplamp, and taillight. I have built a tire carrier of my xj. I want another light like I had, looks like gen-right doesn't have them any more. Who make those or...

Kinda sounds like a 80s band name. Hi all, I installed upper and lower control arms in my 89. Bds fixed length uppers and ruffstuff single flex adjustable lowers. Both short Arms, I am around 2.5" lift with 31" k02 The bds have a large rubber end, I also pressed in new axle side bushings. The...

Im giving myself a little DIY project, fabbing up a spacer and plating the outside. . Im hoping some one would know off hand what is the over all width of the spacer? thanks, Kyle.

Happy Thanksgiving to all!! I'm fortunate to spend this one on the east coast, close to where it all began. I hope every one gets a hot meal tonight -Kyle

I scored a zj for free. Im going to take the front ujoint axles and front driveshaft. master and brake booster. Intake, harness, ecm (everything to someday convert my 89 to obd2). That's all I have planned to do. It has a d44 rear, I don't care for it, but it has disc brakes. Are the discs...

Is any body familiar with this area? A friend and I where thinking of going out there probably the first weekend of December. Is it still open then and if so what are the conditions usually? Snow? rain? thanks, kyle, Bend.

89 4.0 aw4 231. I still have a functioning CAD d30. I installed a PORC sye about 4k ago. since the main shaft is larger they have you remove the needle bearings in the front sprocket chain drive. Since I still have the CAD and the chain is not spinning while the mainshaft is, will the sprocket...

89 with idiot light IPC. When its cold out the speedometer it self make a squawking noise, like dry plastic gears. I haven't tore into it yet. Just wanted to know if I can take the iPC apart and lube the mechanism for the speedo. Also,what lube would I use? graphite? thanks, kyle.

'89 aw4 231 8.25 I'm at about 2.5" lift all around. I need a sye. I don't now how people get away with out one, I guess I'm that lucky, anyway.. Will a auto xj front driveshaft work on the rear post sye install? I have a ZJ front driveshaft, it had a 4.0 aw4 242. It looks about the same length...

Does anybody know the conditions out that way? Might do a wheel/hike date with my lady

89 aw4 np231 8.25 d30 2" lift Ok, Ive had grinding noise with light throttle at speed ive been tracking down for, oh.. 5months or so. It happens at 35+ mostly. My pinion angles are within 1* and I have no vibration. New u joints, swapped d35 to 8.25, used the d35 shaft so I have plenty of slip...

How far does the rear slip yoke travel when put through a complete rear suspension cycle? Say on a older style 231 with internal slip yoke

Anybody else need to shim the rear pinion down after 2" long leaf aal? My angle finder shows I need to angle the pinion down 4*. My theory is it put more curve in the leaf pack so the shackle angle is closer to vertical, pointing the pinion up. Any insight? Btw: 89 np231 aw4 swapped from d35 to...

Im looking for OME 2" leaf springs. Where do I buy them and what is the part number? medium load. Ive searched and haven't found what im looking for. OR.. does anybody have a suggestion for a 2" leaf spring"?

89 4dr 4.0 aw4 What would be the effects if I removed the short factory overload leaf? I have a 2.5" RE long aal that put the rear to 3". I'd like it to be @2.5" Thanks

'89 4.0 renix Whats a good replacement brand for my renix? Other then the obvious factory unit. thanks

89 4dr 4.0 np231 d30/35 235/75's I have had a rumble in the driveline since I lifted from 2" to 3". I didn't have this issue before lift. about 2000 miles before I lifted to 3" I overhauled the dana 35. All the fluids are clean as new and the jeep is obsessively maintained. After 3" lift I...

I am in the reassembly on my 231 in my 89. Im deciding to use the original steel range shift fork, which im not sure if its the cause of my coast grinding noise, or use the new aluminum fork I have? which is better? thanks!

'89 4dr power nothing. She was broken into last night. About $600 worth of items taken. Its time for a alarm. What have you installed for aftermarket alarm? What do you like about it? Has it failed you? I don't care for remote start, but I do want remote door lock actuators for the front doors.

'89 4.0 aw4 np231 d35. I installed these all and I am at 3" lift in the rear now. I know they will settle somewhat, but will it be .5"? I didn't want more then 2.5. I was hoping they would be 2.5" then settle to 2". Has anyone else ran these and what is your experience.? Thanks!