Search results

I put in some used RE 3.5 packs and they have settled to about 4 even on both sides. I greased up the bushings and tightened everything once on the ground. Whenever i have over 200 or 300 lbs in the back the jeep seems to ride much smoother and takes bumps much better. The shocks are not...

I need a driveshaft shop in the area of central jersey to get a driveshaft balanced that got a weight knocked off of it. Or i could use a new front double cardan shaft if anyone knows a cheap junkyard that would have good prices on an 231-aw4-dana30 30 inch long front driveshaft.

Does anyone know what the name of the post was where it was a guy talking about living in his jeep the past couple months and he had a link to an album for moab and arizona and different areas out west. I had this picture as my desktop background but recently lost it and wanted the one with a...

where can i find the stock rubber bushings that go on the connection between the center link for the steering and the right wheel assembly. The bushing there now has a hole in it and it wont hold grease and is giving me a shitty ride because of the lack of support. Some of my other bushings in...

I have a stock front driveshaft from a manual 4wd xj.. it measured 28-31" and the U joints are all good. 20$ Also have a stock slip yoke driveshaft of a 4wd 01 XJ. 60 k miles on it. U Joints are good and no play in slip splines. Stock XJ leaf packs (60k miles) with a 3" long RE AAL...

Right now i am running 4 inches of lift in the back with a 231 and an 8.25 rear. I worked my way up from 2.5* shims all the way to 6* i have now. I still get some vibes over 60 and im thinking my pinion is still too low. Should i go up to an eight degree shim or is something wrong with this...

RE 2.5" AAL. Used for 2 months and only 1 k miles. It is currently installed in a stock set of packs with 60 k miles on them, but the AAL could be taken out. Almost brand new with no sag on it. Asking 40+ shipping for AAL and 55 plus shipping for full packs with AAL. Central New jersey.

i just recently did the H&T by RE and set it up with a 96 cherokee front Driveshaft. I have an 01 with an 8.25 rearend and 231 tcase and it seems as though the new driveshaft is an inch or two short. I am also using 6 degree shims and the angle is still not enough. Can anyone recommend...

-4 Stock XJ alloy wheels, 5 on 4.5, 15x7, 5.5 BS with goodyear RTS tires (half tread). 200 $ + Shipping Not my jeep, but same wheel & tire setup. -Stock XJ Coils 50k miles on em 10 $ + shipping -Stock rear slip yoke driveshaft, 60 k miles, good u joints and good slip yoke no play at all...

recently i have noticed my front tires are angled somewhat outwards, not severly but a noticeable angle. Like this front \ / | | back My question is, is some angle in the front tires outwards normal and if not how can i fix this. Is is the tierod that judges this angle or what.

I currently have a uniden 520xl cb and a magnamount k30 antenna on my roof. I ran the wiring straight from the battery, both pos and neg, and the antenna is in the center of my roof. When i start the engine up i get the engine popping that increases with rpms. If the antenna is unplugged or i...

Alright this is just a quick question about a magnamount antenna. Would it create any rf noise if i ran a hard line coaxial cable from the cb to the trunk and made a coupling there so i could screw a magnamount antenna on when i needed it. I wanted to put on a fiberglass on the rear quarter...

lots of stock stuff for sale.... -4 Stock XJ alloy wheels, 5 on 4.5, 15x7 i tihnk 5.5 BS with goodyear RTS tires (half tread). 225 $ + Shipping Not my jeep, but same wheel & tire setup. -Stock XJ Coils 50k miles on em 20 $ + shipping -stock lower control arms 50k miles 10 $ + shipping...

jks quicker discos 3.5" +

i recently went through the RE links for a 4 inch lift using the homemade cotter pin hitch pin method and wow did that suck, wat a PITA it was to reconnect even if the ground was close to level. Then i cut my RE links and went to the hardware store and tried to copy their gen 1 disco set up and...

Is there any way to set up a stainless 3 ft whip in the radio antenna location and run both the radio and the cb off that one antenna (not at the same time of course). Could i just pull that mount out, run the coaxial to that spot, hook up the antenna to both the coaxial and the am/fm lines and...

If i take off the rear driveshaft while doing the slip yoke - fixed yoke swap and i need something can i drive around in 4wd using only the front wheels as power and leave off the rear DS. Im not sure if a free moving yoke on the back of the T case will cause problems or not. Its not...