Search results

I have to replace the gasket between the Y pipe and the pipe that goes to the cat convertor (federal emissions). There are three fasteners on the flange but are quite corroded and have no nuts on them. Can someone tell me what size they are so I can get some new ones when I get the gasket? Thanks!

Easy question I just can't get right off. I'm putting in Dual E fans for the radiator, I want the computer to run them (no extra switch). how do I wire the relay to trigger them as they are ground triggered on a 99 ? I can wire positive triggered easily enough, for some reason doing it with...

Did some searching, no results for some reason. I know I"m not the only one with this issue. 99 with 4.0 135k miles very well cared for. I noticed some oil on the pass. side and checked the valve cover, it was leaking. Replaced it and cleaned the motor, now I see oil "seepage" coming from the...

My electric radiator fan lost a blade today. Anyone know where to get another?? I have a new assembly on the way and I'm thinking of converting to 2 e fans.

Hey fellow Jeepers, I need a hand!! I'm in Redington Shores FLA on vacation and the battery has gone dead on my WK!!! I need to get it jumped and get to Autozone (few miles away) to get it replaced. I'm not going anywhere so any time Tuesday is cool. I'm online a lot so if you respond I'll get...

I was picking up an AC compressor from a guy and saw what I thought was an np242 xcase. The tag said 260. He said it came from one of many of his cherokee collection(all late 80s to mid 90's). Never heard of one. Has anyone else?

Has anyone ever put 97+ hatch props on a pre 96? Can it be done?? I searched but didn't see anything right off.

My neighbor has a rolled zj v8 and I'm wondering if I can use the E fan from it on my xj?? Anyone know?

Just had my charging system checked at AZ and my Alternator is putting out 13.8 volts. Should I replace it, let it go a while or forget about it? I do have a spare.

My steering wheel is rocking back and forth when I make turns at low speed. I had my son watch me turn a circle in the parking lot and he could see the wheels moving in and out as I turned. I'd like to fix this before fall. Here's where I am on the process 99xj All TRE's are new in the...

I just inherited a 2WD AX15 (it's for sale). I'm wondering if the slip yoke is the same size as the output yoke of an np231? It has 26 splines. If it is I can do a HNT like the one GoJeep has!!!

I"m in the process of making big changes to a toy xj. I just bought a 89 YJ with a ax15 trans and want to put that trans in my 92 xj (has a ax15 that's bad). is that a direct swap? Thanks

I"m looking at a new muffler on the Jegs site. there are two models. One is 14" and the other is 19" I think. What's the difference? Can't I just put the smaller one on and add a piece of pipe between the cat and the muffler?

I was at the stealership the other day and they show an "extreme duty LCA" for 00-01's anyone have them or seen them? I didn't think that OEM did that. I'd like to know what the difference is cuz I'm curious.

I just got a FREE radiator that doesn't leak (mine does). But it was full of nasty brown gunk. I've run the hose through it in both directions for an hour. I want to make sure it's really clean before I install it. Anyone have a really good suggestion for what to clean it with?

I have a really wierd vibration. Arrives at 59 mph and stays through 70. If I coast to a stop -like an offramp- it barely does it. Under braking is there also.I have changed the following: All TRE's Track bar (JKS) all bolts are TIGHT New tires balanced (tried rotating) Axle Ujoints I welcome...

I need a new cat, muffler and tailpipe, any one know of a great deal out there? I don't want really loud (like a flowmaster) as it's a DD.

I have a 91 np231 from a YJ. I haven't taken it off the trans (manual) yet. Might anyone know what the input spline count may be?

I just replaced my rear shocks and as luck would have it, the lower mount broke on the right side. GRRR. I cut the stud off and then spent a while drilling a 1/2" hole in it. I ran to NAPA and got a repair kit but it doesn't fit! The threaded part that goes through the mount isn't long...

I'm in the process of swapping a 4.0 into my brother's wrangler. Wrangler is a 2.5l with an AX-5. He wants to keep the manual trans. does the AX-5 bolt to the 4.0 or do I need to find an AX-15? Thanks!!