Search results

What would y’all recommend ? Jeeps is a 99 xj 4.0 auto with 35s” hpd30(spartan)/8.25. Not sure if I should go 4.56 or 4.88, also what about speedo gear? I have the right one in for 35” tires and 3.55 gearing at the moment. Will be dropping it off at shop in next week.. Sent from my iPhone...

Looking for a np242 for my 99 xj mines staring to get noisy, need one to swap then I can build mine. Also after researching mine has a 91 np242 in it with the 96+ tailhousing Thanks Jon 336-817-4681 Sent from my iPhone using Tapatalk

I have Oliver’s driveshafts front and back and there about 1 year old. I’m assuming as I have narrowed down the squeak that the front drive shaft cv is squeaking, on my double cardone shaft I have a flat head screw that I can take out is that where I would use a grease needle once removed? Also...

Ok I’m brain dead from reading looking for help 99xj hpd30 Jeep drives ok but a bunch of wondering, I’m assuming it cause of caster. I’m at 7” lift pinions is 1-3 degrees off but no vibes ( pinions down a tad ) positive negative caster explain. Looking at Val joints there in line up and down...

I have a 99 xj, I picked up a 95 block that I want to build. I noticed that pistons split year from 90ish-95 to 96 up. Why is that? I wanna order pistons bored .030 over but don’t want to order wrong ones, anyone here that can help?

Ok so I have a 99 xj with 6.5” lift. Everything is new under her. My issue at hand is a little wondering in steering, and now with new steering set up a slight case of bump steer, I know I have to give a little bit on caster vs pinion angle but with almost no to minimum front driveline vibes...

Looking for one 35x12.50r15 Goodyear mtr located in Winston-Salem nc. Old style Sent from my iPhone using Tapatalk

New everything under my xj, new 4.5 re superflex kit with acos. ( sitting at 6.5” front and back ) re control arm drop with supports, re heavy duty trackbar with trackbar bracket and cross support. New drive shaft rear ( fronts ordered, stocks in now ) new front upper bushings in axle, all tie...

I put a superflex 4.5 on my xj plus Acos adjusted to 1.5, I also did the re control arm drop, my problem is that the re fixed lca is 16”, which is to long with my setup. I was hoping someone had a set of re superflex adj Lcas that could measure Them from bolt hole to bolt hole at min position...

I have a 1999 xj and want to upgrade alternator and wiring, can someone tell me what alternator I need? ( wanna do around a 160amp ) and I can't find nothing on the wiring either was hoping to purchase a kit from 5-90 but seems he's no longer around from the searches I have done! Thanks...

Need new bushings in my JKS discs on my 99 xj as one has blown out! Thanks! JMOliver

I figured NAXJA could help with this! I have a 2001 Jeep Wrangler with 4.0 and 5 spd. Jeep has coil packs, Ok here's what I need help figuring out, jeep will start up and idle and when it gets warmed up it will drop to appropriate rpms. At this point it has just a tad of a miss thats not even...

Ok i have never replaced the alternator on my jeep and i assume its Original! ( 185,xxx ). I have a little system and would notice always that at a stoplight at night ( Or day with rear defroster ) the amp gauge would go from like 14 to 12 at idle when systems bumping. once you take off it would...

Specs: 1999 Jeep cherokee, 4.0, 187000 Miles, Auto Jeep has no codes ( I checked with my scanner ) Jeep will start right up and idle fine ( Sometimes has a little miss ) when you take off for the first time during the day it wants to bog down around 1500 RPMs, you put your foot in it and it...

OK so i have a 99 XJ, I ran the wire from the PCM into the cab to a switch. Heres where i ventured off. On the Cluster i have the arrow pointing up for gear shifts. I pulled the bulb out and wired it by itself, Then put it back in ( It dosnt have connection to the cluster board anymore). I then...

Specs: 99 XJ 3 inch coils on front with 3/4 spacers. Rustys Adj. Lower Control arms. Didnt notice this until i installed my Brown Dog MM ( Poly ) At first start up and when the a/c is on my front driver coil spring is rattling. When it does this i can reach in and hold it with my hand and it...

How tight should the threw bolts be tightened? I know the instructions say not to over tighten. Thanks JMOliver

Ok so I'm tired of replacing driver side engine mounts. What do you guys recommend? 99 xj 4.0 Thanks JMOliver

First off Im Jonathan ( 27 ) Finally set up a user name, I wont lie though i have been looking around here for a while. Seems like a great place, Im Also on NC4x4.com. Located in Winston-Salem and i currently have a 99 XJ with all the mall crawling Assesories ( 4' Lift, 31 MT's, Lights, Some...