Search results

I picked up a 90 f350 kingpin and now have to turn it into 79 dimensions. I have already removed the drivers side axle tube. I noticed the inner most side of the tube is machined down to accept the seal. Does anyone know a place that sells replacement tubes I can cut down to the length I need.

i need a set of stock coils so i can weigh the rear end of my jeep to buy coilovers. they need to be the same springs and hopefully you know what year they are off of. i am willing to pay 20 bucks or you can let me use them for a week. thanks

1 is from a 99 xj 3.55 ratio 29 spline. the other is from a 2000 xj 3.55 ratio 29 spline. both are open differentials. the 2000 had the shock mounts cut off other than that both are complete and ready to bolt into your project. 150 o.b.o. each. pm for more info

the past couple weeks or so when i floor the jeep and it downshifts to 1 or 2 the rpm will climb up to 5200 then bounce off the limiter. to shift i have to let off the gas and it will upshift normally. it only seems to happen a WOT. I tested the solenoids all 13.1-13.3 ohms. tcu has power and a...

to start off for the past couple times i have drove the jeep i noticed the locker would lock and unlock going in a straight line on the road. the 8.8 is a 97 and it is a detroit ez locker in the carrier. so i took it apart to see what was wrong and found one of the side gear thrust washers had a...

i have a 96 134a compressor to replace my 91 r12 compressor that seized. My problem is that the fittings are different on the 91 to 96. i can't seem to find just the fittings without having to get a new compressor. So does anyone know the thread count on the suction and discharge ports of a 96...

does anyone have a set of r-134a compressor fittings. my r-12 compressor went out and i had a spare 134a compressor. it is the fittings that screw directly on to the back of the compressor. it's for oba not ac. let me know if you have some or know where to get some.

i just got back from the ecology on energy way in chula vista. in my hunt for seat belt buckles i found a dark blue xj with a 44 rear end. i have a 8.8 already so i wanted to let you guys know so someone could go get it.

I'm just wondering who is going. i would love to meet up and do a run with some fellow xj's. I am heading out thursday night and won't leave till sunday morning. since the wife is not going this year i plan on wheeling the whole time or untill something breaks.

91 with a 96 motor a 98 aw4 and 96 torque convertor. my trans started leaking again today. so far this year i have replaced the front pump output seal twice. the last time was three weeks ago and it is leaking again. the trans is not overfilled and it is not coming out of the vent tube. i drips...

while i was at the desert last weekend i would get a ce light and code 51. i usually get this at wide open throttle after about 15 min or so. the only other time i get it is when i am climbing the grade home and at wot. i am wondering if i put a vaccum regulator in line of the fuel pressure...

me and a group are going out to play in the sand. is anybody else planning to go out? we could meet up and go duning. i will be out early thursday afternoon.

can you swap 2wd hubs with 4wd ones. they look the same but the 2wd ones have a stub shaft where the outer axle shaft on a 4wd one would go.

since monday morning the jeep has been running at about 2600 rpm at 65 mph in which before it ran at about 2250 at 65. i have no check engine lights on and all my connectors are plugged in. the fluid level is fine and not discolored. i run a large external coller so heat should not be a issue...

i am putting a 96 4.0 in my 91 .my question is if the fuel rail off my 91 is a direct swap to the 96. i want to keep the injectors in the 96 and just swap the fuel rail.

my wife totalled the 96 so i want to put the gas tank in mine since mine has more dents that the body. my question is do i need to change the pump and screen assembly out of mine into hers for the swap. or can i just swap them as is .I know the tank itself is the same but i don't know about the...

91 4.0 aw4 d30 disco my axle shafts stopped locking. the vaccum is fine i tested it and the disco motor itself is fine putting out a strong amount of resistance. i also replaced the pass side u joint today. i can manually lock the two shafts if i take the motor housing off and lift the wheel...

book says something about injector circut current. it is a 91 4.0 aw4. it threw the code while i was climbing the face of a large rock and i noticed the light flicker. after i got to the top i turned the jeep off and on and for the rest of the trail no more light. any thoughts would help.

i finally got around to finishing my front fenders and front bumper. the bumper also serves as the air tank for my oba. tell me what you think. i will take pics of the fenders tommorow.

i finally upgraded my alternator. i used a 120 amp model from a 97 grand cherokee 5.2l. the mounting dimensions are the same on the two the case on the 120 amp model is just a little bigger. i only had to do about 5 to 10 minutes of grinding on the cast bracket. also the support brace needed a...