Search results

I've been searching the forums to decide one what radiator I should get. I'd really like the spend less than $200 on a 2 row replacement. I don't need anything better than stock for what I do. It seems like a lot of the replacements have people coming back to say that the radiator failed after...

lower the angle on the rear output shaft. I did a really quick job of measuring the angle of the output shaft and the rear pinion, I will double check it and read a lot more so I can fully grasp the concept. The output shaft was 1* and the rear pinion was at 6*. So how much does say a 1"...

I've got some minor vibes when accelerating, nothing that has made me want to drop the T-case. I'm talking a 2" lift on 30's with a 2000. Been driving on the highway a lot more lately and realize I have a problem. At 70mph plus I have some really loud noises coming from what sounds like the...

Just got done replacing my blower motor with the Four Seasons 75712. It whines on settings 1 and 2, and makes a clicking noise(sounds like it's rubbing something) on settings 3 and 4. Not sure if I got a bad one, or if I am missing something.

Title pretty much says it all. I replaced the blower motor resistor a couple of years ago because the old one stopped working and was rotted out. Today speeds 1-3 stopped working again, so I went to clean the connections and check things out on the resistor. When I touched the plug, the blower...

This place has a wealth of knowledge, and I hate to be the guy that asks a question thats been asked many times before simply because the search feature doesn't work. I can't use the search feature, as it never gives me usable results. I do a lot of searching on other forums, but this is the...

Went on my first wheeling trip last weekend and it was a lot of fun. Thought I got away without breaking anything until further inspection today. Looks like I blew out one of my front axle seals. I went to check the fluid and it is brown now. Does that mean that water got in there? One of my...

What the hell gives? I got the most expensive precision U-joints that NAPA had and put them in 7 months ago. 5,000 miles later they already have play in them and are making noise. They've been greased twice. Seems like every time I fix one thing I find two other things that need attention. Damn...

Going to do a 1" T-case drop on my 2000 XJ with a 3" lift. I have the square tubing, but would like to pick up some new bolts. What size bolts do you guys use? Thanks!

Swapped these out this summer, snaped some photos so I could post them eventually. Been having some MPG problems. You guys see any issues with these?

Anyone know the size of the 12 point bolts that hold the hub onto a Dana 30? Three on each side. I have to get my U-joints done, and those bolts are rusted to hell. Thanks!

Do you have any MPG problems to report? 12-14mpg on average isn't fun when I used to get 16-18mpg on average. I can only get 16-17mpg MAX when driving 65mph long distances, and I used to get 20-21mpg. I've got everything else I can think of checked or fixed. This Bosch 02 sensor is the last...

Finishned my first lift yesterday, only was supposed to be a 2" lift. Everything went too easy of course and now my rear end is sitting 4" higher than stock. It mesures 21" from the center of the hub to the bottom of the fender, and just under 21" with 400lbs of crap in the back. How long...

Hey guys, I recently got a new AC compressor and a new accumulator. Then it was vacuumed and charged, as well as oiled. Now the clutch engages, and the compressor seems to cycle properly, however it is somewhat loud when accelerating at lower speeds. Its basically just a whirring noise. Hasn't...

Hello! This is my first post here. I have done a lot of searching tonight and have came up with no answers. Ok, A while ago I replace my steering box, right after I failed to bleed the system all the way and my stock power steering pump started to whine. So I got a rmf. one from autozone. It...