Search results

Hey guys, I need a little xj knowledge here. I've got a 93 country model that I'm having electrical problems with. A few months ago I started having problmes with the interior lights staying on and running my battery down. I just took the bulbs out since this isn't a daily driver. Then about a...

hey guys, I've got a problem and need a little help. A few weeks ago I went on little trail ride. About halfway or so My alt started to die. By the end it was only putting out about 9 volts according to the gauge. When I started to pull out onto the main road my trans wouldn't shift into first...

Last night me and some friends did a little wheeling. Nothing serious but there was alot of mud and a few hill climbs. When we where almost out I noticed my alt wasn't fully charging. Not a big deal, it's got over 200000 miles on it so it's probably time for a new one. When we went to get on the...

I've got a 93 country that I'm trying to start. I just swapped in my stroker and need to break it in but I'm not getting any fuel. The pump will hum for a second then stop. I jumped the wire on the ballast resistor staight from the battery and the pump works ,so I know the pump works but after...

I've run into a little snag in my swap. I'm running a renix block for my stroker and swapping it into a 93 body with the 93 head accesories. The problem is two of the bolt holes aren't drilled on the renix block. the place where the coil bolts to the original block have the bosses cast in place...

hey guys, anyone have a factory wiring diagram for the dash and interior? I'm swapping out my old wiring harness for a newer one and need some help. MY jeeps an 89 model and my parts jeep the new harness came from is a 90 model. They both have the same accessories and I thought they woud be...

I got a problem with my 86. I did a 3.4 swap and had it running with the original varijet. It started having problems and even after a rebuild still wouldn't run well. I got a good deal on a edelbrock 4 barrel intake and a 390 holley carb. I rebuilt the carb and set the float level on the...

I just picked up a dana 44 from a friend's 87 for $100.00. It's in good shape overall and even the drum brakes are in good shape. but the pinion seal is leaking. My question is can this seal be replaced without messing with the bearings? is there a crush sleeve in a 44 and if so will it have to...

does anybody here know if the factory gas boost will work without the abs computer? I've got a 90 model that was flooded and the abs computer had water pouring out of it when it was removed. I don't know much about these types of brake systems but I do have a stock 86 booster and mc I can...

I need a new drive shaft and I was wondering if I can get some opinions. I've got an 86 pioneer with a swapped in 3.4, stock tranny and transfercase with about 6.5 lift. My original gkn was in excellent shape but I know it can't handle much lift. Of all the crap I've collected over the years I...

I've got my 3.4 swap up and running but the rochester is a piece of junk. Rather than rebuild it I've decided to go with a 60* torker 2 and holley 390. Does anyone have any tips for setting up the holley for better off road use? Any problems with this swap other than clearance issues with the...

I'm doing a 3.4 swap over the next week or so but I have a few minor problems. The first one is a sensor just behind the timing cover. I think this a cam postion sensor. Does this need to be removed and blocked off, or can I just leave it where it is? Second, What is the difference btween the...

I know you need to use the 2.8 flexplate and it needs to be neutrally balanced but can you just take off it's weight or is there more to it than that?

I've got an 86 complete with a 2.8 rodknocker,auto and 207 tcase. I'm swapping in a 3.4 as soon as I can clear some space in the shop but I was wondering about the tcase. I've heard the 207 isn't that strong so I've thought about swapping it out as well. I've got a 231 from a 88 blazer sitting...

I've got ez locker for sale. It fits a dana 35 c clip 27 spline axle. It will not work with a non c clip axle. I'm asking $250.00 plus shipping. I don't know how to post a pic but I will email anyone how want's one. Thanks for looking.

I'm looking at rustys 6.5" lift kit for my 86 xj wagoneer. www.Tellico4x4.com has them for $999.99 plus shipping. The kit looks pretty good and I know I'll need a sye but other than that does anybody have any experience with this kit? I have heard good and bad about rustys stuff and I would hate...