Search results

So I started a build thread about a year/ year and a half ago about my 609 and 13 bolt build over in advanced fab. Which was probably going to escalate into an entire build thread but after I got laid off, money got tight and I haven't quite gotten around to getting my red letters back. But I...

In great shape. A few scrapes. Comes with tie in mounts. In bullhead city az. Will ship on your dime. $450

So i have a pretty stout 16x7 flat trailer with railings (will have to get a pic in the morning) and since i am making the switch to one tons and 40's... i am going to have to widen it a few inches, which means getting rid of the railings, reinforcing, and building new drive over wheel wells...

So after shredding apart a hp d44. I decided it was time I quit braking. A rear 60 had been sitting in my garage for awhile. So I found a good 14 bolt and sold the 60 and bought the 14 all in one trip to San Diego. After looking for months for a hp 60 I gave up and decided to build a 609... the...

I'm building a 609. My issue is I don't know where to have diamond axle set my pinion angle and castor. I'll be running a Tru hi 9 third and Clayton 6 1/2 coils. I thought about just telling them to put the pinion angle 2 degrees over the stock xj angle. Assuming that with the lift two degrees...

Not sure if this should be here or not. Please move if necessary. So I have a few questions. Anyone have any experiance with the hi 9 thirds? If so where are your weak points? What locker are you running? Would you change it? I know ox doesnt make a 9in locker :smsoap: What housing are you...

Cash in hand. Its just that time.

Yup its time. Cash in hand.

89 renix 4.0 Just did the 96 booster and mc swap got it all together and bled the lines. When I started it I fried the insulation off a wire that goes to the sensor in the positioning block. Any ideas on what caused this and is it needed?

So im looking at rockauto's catalog and its giving me three options. One of which says engine vin "s" with vacuum booster rod code 19902. Can anyone tell me if this is the booster I need? Itll be going in an 89 renix.

So last weekend my steering column basicly fell apart in my hands. Im looking to swap in just a shaft and quick release steering wheel. It gets towed to the trails and only driven to the river. Everything necessary will be put on a switch. Any ideas on where to find the parts im looking for? I...

in bullhead city custom truss custom disk brakes BTF diff cover 4.88s aussie locker comes with u bolts and custom 3/8 spring plates with bump stops

located in bullhead city az (just off the 40 in the north-west corner) custom truss custom disc brakes 4.88s aussie locker BTF diff cover custom/raised shock mounts comes with u bolts and custom 3/8 spring plates with bump stops

I have no power to my #2 (radio) fuse. thus no power to my 12v radio wire. any ideas? 89 renix

I have no power to my #2 (radio) fuse. thus no power to my 12v radio wire. any ideas?

152xxx miles Shifts great Swapped for a 231 in bullhead city $100 Get it outta here too much xj stuff

I have a dana 44 with disc sonversion and custom truss that i ran i my last jeep (r.i.p.) that was in it when i rolled it. It was a pretty distructive roll and now im putting together my new jeep and i noticed when i spin the yoke the discs wobble. I swapped in my spare set of shafts and they...

did anyone have to do anything to the stock braking system? someone i know suggested putting in a zj distribution block for a better ballence of the brakes.

im building a rear 44 out of an xj and was just wondering if it will accept "thick" gear set?

im building a rear 44 out of an xj and a guy at work has a set of new "thick" 4.88's. will these work in my housing? whats the deal with "thick gear sets? thanks