Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
I'm looking to sell my rear Ford FF Dana 60 set up for 4 link and coil overs.
I got this axle as part of a package deal. I don't need to sell it; but if I use it I will be cutting off the 4 link brackets and using it in a leaf spring set up on a Durango. If I sell the whole package, I may go...
I have changed my mind and I am selling my old XJ.
84450BB Bike Black
I have OR-Fab quarter armor with rail that were mounted. I have the stainless bolts and washers but you will need qty 22 nutserts 5/16" available at fastenal for about 80 cents each. The previous owner got some red paint...
I am building a 2nd 4x4. I would like it to be an XJ but it needs to be able to tow a 5000lb 2 door JK on long trips over the mountains of Colorado.
The parts I have now:
Dana 60 front and rear axles with disc brakes, gears TBD
Atlas II transfer case
Currently have AX15 but I'm working on...
I bought my old Cherokee back and I am pulling the Atlas II transfer case and maybe the AX15.
I'm looking for.
transfer case 231J 23 spline
AW4 (if I can find one cheap enough)
driveshafts
taillights
I will add more to list as I figure out what else I need.
Thanks,
Rob
I'm partial to the XJ but I'm also looking for other ideas on what to buy that I can use my Mustang 347 motor with stand alone ecu. I'm looking to spend 4-5 grand on a chassis.
I would like to put a manual transmission with overdrive behind the motor. I have a Mustang t5 but I don't know...
Came off of a 94' 4.0, part # 99411S.
Worked well but has been sitting in my garage for 3 years. I no longer own an XJ.
$90 OBO
For quicker response, please email [email protected]
Thanks,
Rob
South Colorado Springs
I am cleaning out my garage and I still have a custom set of Ford 9" axles front and rear.
Both center chunk:s are 4.10 gears, 31 spline Detroit Lockers with nodular iron carriers, Daytona pinion supports, and solid spacers. Both carriers come with a spare yoke purchased from Currrie.
The...
I need to find a good place in Grand Junction to meet FearNoFish to transfer a couple of engine blocks from trailer to trailer. I am going to bring my engine hoist to make it easier. I am looking for a truck stop or some other place with ample flat parking?
Also what is the weather supposed...
I am selling my collection of IH Dana 44 parts. I am not willing to separate the parts; I want to sell the lot and be done with them. I am not very knowledgeable about IH parts and I don't want to figure out all the details.
Pair of flat top 5 lug, 8 bolt spindles with high steer arms and new...
Ford Explorer rear disc brakes for 8.8 and 9 inch axles.
There is a dent on one of the backing plates, but it doesn't rub on the rotor or affect the brakes.
The stock rotors are drilled for stock 5 lug and Mustang 4 lug.
I will also throw in a new set of rotors that are drilled for 5 x 5.5"...
Here is my other toy that I need to complete. I have had a little more time to work on it now that I don't have my XJ. Unfortunately I don't have as much money to spend on it.
Engine mock up.
Here is the car in many pieces.
Good Brakes
I have an old 160 amp Link-Arc welder that I purchased in the 90's. It has been stored in my garage since 2001 when I joined the army. The alternator was repaired once with new bearings after my harmonic balancer fell apart. The shop that repaired it sprayed the alternator black without my...
I have a used Hesco Aluminum head with new dual valve springs, retainers, keepers, valve seals and custom camshaft by Camshaft Innovations. The head was checked and measured by McCabe Motorsports. The dual valve springs and seals were installed American Speed Center. The head has not been...
I am having problems with our furnace.
The LED is blinking fast, which is normal when it is calling for heat. The furnace comes on briefly for 5 seconds and then the flame goes out. The status of the LED doesn't change and after about another 15 seconds the furnace restarts again and turns...
I was given these radios by a contractor that left Iraq while I was deployed. I originally had the mics for them but they got lost in my many moves while I was over there.
Are these radios any good, and what can I do with them?
I could only find 1 part number: IC-F121S
I sold the XJ so now I need to get rid a few remaining parts.:tears:
4 Rancho RS999012 XL 12" travel shocks and Wireless controller (RS999075).
2 shocks have 2,000 miles of street only use and the other 2 are still in unopened boxes. The Controller box has been opened but nothing has been...
I had the chance to play with my new Rubi today. My wife and I went up Rampart Range road to Schubarth Road. It was just an opportunity for me to try out some of the 4wd features. We didn't go all the way to the end because we were driving solo and had no recovery gear. It was fun and we...
I have an incomplete 4.6L stroker motor for sale with aluminum head: $1600.00
The original owner destroyed 3 camshafts within 10,000 miles. The 3rd camshaft was installed without the front retainer button and spring. The cam bearings will need to be replaced and I would look at the other...
I will be picking up a brand new 2009 2 door Rubicon this next Saturday from Iowa!:party:
I will finally have a nice vehicle for work and play. I will have more time to enjoy the outdoors and wrench on my Mustang.
Unfortunately, that means I will be getting rid of my XJ and all related parts...
I'm looking to buy stock good condition suspension parts:
Upper and lower control arms.
Coil Springs
Leaf springs
Shocks
Stock 23 spline transfer case
stock drive shaft for AX-15 and 231 case and Chrysler rear axle.
I'm not looking to pay a premium for these parts, I just want to put my XJ...