Search results

Ok, i'm about to do an axle swap, in the rear I'll have an Isuzu rodeo Dana 44 with the 4.30 thick gears (93-97) and the high gear carrier, it's the stock set up. In the front it will be an 86'+ wagoneer dana 44 and I want the matching 4.30 gears. Randy's ring and pinion doesn't seem to sell...

So I've been reading reviews and what not and decided I want to go with the Polk Audio db5251 component speakers, check em' out, http://www.buy.com/prod/polk-audio-db5251-5-1-4-component-system/q/sellerid/18756548/loc/111/204254735.html Anyways, I've looked around on the tweeter location and...

I need a new seat bracket for my XJ, not a seat, just a bracket. So If i got a ZJ bracket can I bolt my XJ seat to it without any modding than bolt it onto my floorboard? And these are manual seats not power, thanks. Also, do any of the power lock actuators work in the 97+ xj from the zjs?

It's a front narrow track wagoneer axle. What i want to know is, what do i have to do exactly to make this fit? I KNOW THERE ARE POSTS ON THIS!!!! But I've found too much conflicting info and i want to know how to do it right. I have a 98' xj with a 5.5 inch rubicon express lift on 33's. I plan...

Ok, I've got a 98 cherokee with a 5.5 inch life. I've started having this problem ever since I put steel bumpers on the jeep. Everytime somebody does something stupid like cuts me off or slows down to 30 in a 45, the rpms jump up and the jeep will accelerate to about 6 inches off their rear...

I've got a 1998 XJ 4.0 I6 and AW4 tranny. When I'm driving everything shifts fine but if I get up to maybe 65 or 70 MPH the RPM needle jumps around, not like if you rev it it's like a thousand RPM instant drop and then back to where it was. When it does this the jeep lurches back a slight bit...

I have a 98 cherokee with a rubicon express 5.5 inch lift. If I'm going front dana 44 out of a wagoneer, what should the caster and pinion angle be at?

I would have posted this in the wanted section but it won't let me, sorry... I have a 98 jeep cherokee xj that I'm planning to put dana 44 front and rears under. I'm looking for dana 44s out of a Jeep Grand Wagoneer so if you have a set or just one for sale, please let me know. Tell me what...

So basically, TNT customs is selling this kit here http://tntcustoms.com/fronttruss-wagoneerd4480.aspx which they claim will let you not only weld on this truss to strengthen the waggy front dana44, but will allow you to weld it on with all the mounting points to put it under your XJ. So what...

How many degrees advanced should the timing be on a healthy 4.0l straight 6. Mine was reading 7.0 to 7.5 degrees at idle and it just seems to be running a little ragged. Also, what should the vacuum pressure be on the engine? And how does the vaccum pressure relate to the timing, like...

Other than the electronics, are the housings the same for the pre 96' distributors as they are for the post 96' distributors? What I'm basically wondering is can I take the internals from a newer model and use them in the distributor housing on an ealier model, placing the whole thing on my 98'...

I've recently installed a Melling high flow oil pump on my truck, and broke the tab off of two distributers, i think because of the oil pump. The first distributor I thought was from over tightening, the second one i know wasn't over tightened. It seems like the shaft that drives the oil pump...

So quadratec sells a set of what they call xj pods. Supposedly they replace the rear panels in the back of the XJ and allow you to put an 8 inch sub on each side without using any cargo space. Has anybody tried these? If so, please tell me what you think. Thank you.

I was wondering if anybody knew where I could get a 4.0L roller timing chain. Autozone sells Cloyes but didn't have any in stock, so I went to PerformanceParts.com and ordered one, then they said they had to cancel my order as Cloyes no longer stocks them. So I was wondering if anybody knew a...

I have a 98' XJ with a 5.5 inch rubicon lift and Polyurethane bushings. I've heard that poly bushings will creek when you're driving, but how loud do they usually creek? And does it ever break in to the point where it won't make that sound on every turn and bump? Or could there be something else...

Hello everybody, new to the forums. Alright, I just got my 1998 Jeep Cherokee classic and I would like to do some mods so I had some questions for you guys. It already has a 5.5 inch rubicon express lift, slip yoke eliminator, and quick disconnect sway bars. 1. Dana 44 front and rear axles. I...