Search results

so my first question is do or don't? currently my set up is;rear-factory d44, trussed ,4.56, cromos, arb locker, drum brakes. my front; high pinion d30, 4.56, arb locker. the big upgrade i want in the strength of the front axle, and the general brake upgrade. i plan on going up to 35s then...

What are the dates for this years nwfest run? We usually do middle of June, we did Father's Day last year.just trying to get some trips planned out.we are driving the truck and camper out to Minnesota for two weeks over the 4th of July,and I think we are leaving the last weekend of June.

Need some input. I'm building my sliders and I have a few choices on material for legs. My sliders are 2x3" 1/4 wall, I could use 1" 1/8 wall square, 1 1/4" 3/16 wall or 1.5" 3/16 wall. Also what size flatbar do you all use for the pinch seam. I'll make plates and weld them to my ruff stuff stiffys.

Here's some stuff from this years NWF. Didn't get to much as my phone is full of 1300 pics and videos👍 My wife,kids(1&4yrs old)and father Rory and his wife rolled out Friday afternoon, Set up camp, the next day set out. It drizzled all night so pretty muddy out there. That was fun. The first...

So I just wanted to post up this quick and easy project for the masses. I just installed a tow hitch so I had a rear recovery point. And while I was looking decided I needed a place to put the spare tire until I make a bumper some time in the winter months. So I grabbed some 2x2" 1/4 wall tubing...

I'm having fitment issues with these stiffys, I'm a good 1/4" short of getting to the floor boards. Anyone else experienced this? Should I cut off the lip.heat it up with a torch and press it up and weld? The problem I see with that is it would align perfectly with the seem and all the rubber...

Ok so this was the test run on my revamped suspension, I went to 4.5 rubicon springs, swapped in a d30 hp and rear d44 among other things. Right away there was loud banging and popping from the front left,quick look and found it was the spring rubbing and catching on the IRO track bar mount,no...

Hey, done lots of reading and searching, time for a humans touch. I installed an RE 4.5" lift new stuff. With bar pin eliminators,1" minus on the shocks.(though I did 4.5" rear springs and I talked to RE today and they said they do 3.5" spring and 1" shackle) the rear rides high and I may have...

Hey all, what vehicle's double cardon driveshaft with 1310s is the best to have shortened to fit the xj. I measure 33 1/4" . 2000,auto ,d44,hp30,sye,4 1/2 w/33's

Ok,basic question. What is the minimum/safe travel i need in a drive shaft slipyoke. What im trying to do is use a front driveline the for a rear. I just installed an AA sye, and a rear D44. Distance from yoke to yoke is 32 3/4" roughly. My front shaft is 33 1/2" extended,30 5/8" collapsed...

Does anybody recall the napa part number for the ubolts when converting ujoint straps to ubolts? I beleive i have 1310's. Also are you guys converting over the yolks on the tcase as well? I thought I've seen a thread on this before but couldn't find it, thanks 2000,4.0,abs, unknown year HP D30...

So my new to me, nearly brand new toyo open country has a deep gouge almost to the belt, at least I think. How deep is to deep to use on the road? My common sense tells me to buy another tire and rotate that one to the spare. But I'm in the middle of swapping my axles and suspension and funds...

Im thinking of removing the antilock brake jungle thats next to the booster,so i have room to mount my arb compressor. Has anyone done it? I have long ago ditched the sensors at the wheels. It couldnt be as essy as just undoing all the lines, unplugging any electrical could it.

Like the title says, new in box (though some time ago)RE 4 1/2 " front coils part# 1310 . located just south of seattle 100$

Can i run my bar pin eliminators on bilstein 5100 shocks? I saw they were vulcized to the pin?

Im installing a dana 30 high pinion, and it looks like my RE lca bushings are on their last leg so im trying to find out what ones i got. I got them from CL a few years ago, so unsure of a part#. They are the superflex lca's and the bushing measure 2" OD, with the steel inserts. So large or...

Hey all, im gonna be putting in my sye in this week or next and was wondering if anyone can recommend a good manufacturer on a rebuild kit? Also any upgrades? I think i may need a new chain(yoke moves pretty good, can really feel it in 4low when going from drive to reverse) i think i heard you...

King county is having another big auction this Saturday!i spied about 6 Cherokees (this is where I bought my'00 for 2900$ in 2007) tons of other vehicles and a lot of shop equipment, plus various pallets of brand new crown Vic backseats, lol but seriously they give this stuff away for penny's on...

So I have my dana 30 high pinion and dana 44 off to my buddy's shop getting built, and he calls me over to look at the way the bearing is only sitting in half of the cap. He called Randy's ring and pinion for help, and they said its right and they send them out like this all the time. You see in...

One last trip before I tear down my xj for the big upgrades for 4x4fest.Me and a buddy will be up there around 10am, at the Burnett chevron, blue 00 4door, green Toyota . Come on out