Search results

I am having to put my baby up for sale, this truck is a bit of a FrankenJEEP if you will. It is a trail MACHINE that you can drive to and from the trail, up any hill or through any hole and then drive it home and daily drive it. The Project was about a 2 year build for me that I did all...

I am having to put my baby up for sale, this truck is a bit of a FrankenJEEP if you will. It is a trail MACHINE that you can drive to and from the trail, up any hill or through any hole and then drive it home and daily drive it. The Project was about a 2 year build for me that I did all...

Does anyone know of a low profile press in Crankcase vent filter for a 4.0L from an 88 Cherokee. I have measured the hole and it measures 1" but all the aftermarket filters are either 1 1/4 to 1 1/2 or 1 3/4... It needs to be press in so I dont have to used the factory rubber seal.

I found stock replacement for the vinyl wood grain decals for the XJ wagoneer. I have been looking for a while. It's not cheap but It looks like a pretty perfect match...

I am running 35x12.50x15 MTR Kevlars, I am wanting to beef up my HP dana 30, I am running these other parts too. Aussie locker, 5-760x U-joints with almost alloy kit installed, Gusseted UCA mount, Rustys kit which gussets the top of the long tube and underneath the C's to the tube, also full...

Does anyone know if the JK/TJ Dana 30 sleeves from Offroad evolution will work on an XJ high pinion dana 30 without modification? What other companies make Dana 30 sleeves for the XJ Dana 30

So I still have my a/c compressor on my engine with no lines hooked up to it. Will this damage the compressor? Do I have to worry about one day the pully freezing up and breaking my serpentine belt?

Anybody who has done this swap and used the JKS tie rods with WJ TRE's on a Dana 30. Also I have done a Tie Rod Flip using Goferit offroad inserts. I am having trouble with the passenger side sway bar interfering with the steering linkage between the pass knuckle and the pitman arm. Can...

I have two huge electric fans wired up, they come on as soon as I key on to start the vehicle. Does anyone know of a way to make them not come on until the engine is running or some kinda delay so that I have time to crank the engine before they come on.

I have a friend with a 96 4.0L AW4 and she is having a problem with intermittent starting. The local mechanic has really hosed her out of some serious cash so I'm taking over. OK, so when it doesnt start it just cranks and cranks and no start, so I think about the CPS being bad and replace...

OK, so a lot has happened since I've last updated.. I replaced all ground straps with 4 Gauge Welding cable, I cleaned all grounds and put ox-guard on all cable lugs. I also added some grounds to. My idle is running at about 1400rpm and I have been doing some trouble shooting trying to rule...

I am near Lexington Kentucky in case you wanna pick something up. http://www.naxja.org/forum/showthread.php?t=1062201 I also have 4 of these $15 a piece

I am near Lexington Kentucky if anyone wants to pick anything up. http://www.naxja.org/forum/showthread.php?t=1062201 I forgot I also have four of these rims $15 a piece

Can anyone tell me where this (circled in orange) goes too? What hooks up to this place on the intake manifold?

I get a lot of oil on my air filter, I think it comes down the tube from the valve cover into my rustys air tube and onto the bottom of my K&N filter, It did this also when I had the stock airbox, is this anything to worry about? What does it mean if anything?

I have my oil pan off, my jeep has 160K miles on it, should I go ahead and replace the oil pump? I replaced the rear main seal already. Does anyone have any experience with how many miles it takes to kill an oil pump on the 4.0L.. Also the Block is a 1996 and heads are 1988, is the 96 block...

hood latch cable, dana 44 u bolts from rough country, carb choke cable, stock xj nut serts for rear bumper, stock pitmann arm, newer front brake lines (stock 88xj rubber) bezels, and corner yellow lenses and front lower lamp housings, same as pic below bezels, and corner yellow lenses and...

I am looking for some aftermarket moter brackets for the 4.0L. The ones that utilize multiple bolt holes in the side of the block instead of just the 3 factory ones. PM me!

I am looking for some aftermarket moter brackets for the 4.0L. The ones that utilize multiple bolt holes in the side of the block instead of just the 3 factory ones. PM me!