Search results

Come get them $10 https://photos.app.goo.gl/xwGGkwmbe2gVDCM3A

Come get them $10

Hey All - I've decided it is time to part with my XJ. It has been great, but I just have no need for it anymore as my Dad and brother sold their jeeps and I just haven't used it in years. Description below is from my CL ad. Yes I know the asking price is high and I can be flexible there, but I'm...

Anyone know of a good shop near Sac that could repair the crack, and maybe sleeve the frame rails for me? Is this in a place that most reinforce when they sleeve the frame?

I now have a spider9 so I am selling the old axle out of my Cherokee. Its a '77 Early Bronco 9" (heavy duty housing with big bearing ends) with: Detroit locker 31 spline Curry alloy axles spring perches already set for an XJ pinion set for ~6 inches of lift 70's Lincoln (I think) disks and...

I need to clear out my garage and side yard. Come get this stuff (Woodland). Will not ship!!! '97 4.0 - lost compression on #1 a few years ago and I just swapped another engine in. You can have the stand too. I have all the lifters/rods kept in order as well. No valve cover, no oil pan. It had...

My Dad just got his Jeep back from getting a new rear axle and lockers front and rear so he was itchin to try it out. We decided to check out Barrett Lake as we had never been. The trail was a lot of fun - not too long and not too easy. There was one other group when we got there and a few...

A while back I had my water pump (maybe the thermostat, not sure) replaced by a shop who's competency has since been proven severely inadequate. Within 5 minutes of leaving said shop in 100+ degree weather I turned my AC on and shortly thereafter the temperature went from normal to 260* After a...

!@#*'d my Dad around on a new rear axle/shafts/locker, etc. for 7 months (after taking his money). My Dad goes in last week to get his stuff and a guy working there told him the owner is losing his license for tax reasons. Pretty sure my Dad is SOL. He did a crap ass job on my rear axle too...

Anyone know where to get some custom brake lines made in the general vicinity of woodland (Vacaville-Sacramento-ish)? Can you run braided stainless on the axle or should I only do hardlines? Thanks.

I need a little advice about these brand new custom shafts made by a reputable shaft maker that I got from a pretty well known axle builder. My custom spider9 has been sitting at the axle builders shop for almost 2 months because he was waiting on these 35-spline shafts. They finally arrive and...

http://www.capradio.org/programs/insight/default.aspx?ShowDate=6/25/2008

Posting this for my brother. He's not likely to respond here so call the number below. Vehicle is located in the San Luis/Moro Bay area. Its essentially stock afaik except for the lift installed by yours truly and the NP231 installed by a local shop. Will update with asking price when he gets...

Within the last week or two I have been unable to load the website from my home computer (winXP home ed.). I just get the website not found or microsoft search engine website instead. I've tried deleting all my cookies, history, temp files etc but it doesn't work. Other websites load fine. Any...

I'm running GM steering over the knuckle. I noticed a while back the passenger side TRE was lose at the knuckle and when I tried to remove it the post spun and I had to use a nut splitter, so I thought it was a bad TRE. When I replaced the TRE, I couldn't tighten the nut down enough before the...

First things first, Dynatrac HPD44 4.88 gears, lockout hubs. Changing the gear oil today and noticed waaaay to much metalic paste, and big ole flakes so I took a closer look inside. The gray on the walls is metalic paste. I know basically nothing about working on gears. What is that piece...

I finally finished swapping in a 2000 longblock into my '97. Used everything from the '97. I don't seem to be getting an spark from the coil, but the coil tests good. I am also thowing code 11 - Faulty CPS. CPS is brand new from the dealer. TPS, coil, dist, etc are also pretty new. I tried...

I just installed my new MORE MM and picked up a couple 1/2"x5.5" bolts since I seem to have lost my stock bolts. The 1/2" bolt fits the block side mount perfectly, but won't fit in the MORE mount. So do I try to drill out the hardened steel MORE mount to 1/2", or just go to 7/16" bolts that will...

My brother is wanting to see what he can do in his suburban and wants to try to get to Strawberry Lake, but I think there are spots way to tight for it. Red lake is quite a bit more open except for the last 200 feet to the lake or so right?

Hey! Haven't been around much lately and this is why. Alison Rose was born August 18th at 8:12 PM. She was 7lbs 14oz. She is doing great and so is Mom. Hopefully we'll get to do some fourwheelin again sometime! Takecare!