Search results

'91 4.0, AW4, NP231, Dana 30 front, Ford 8.8 rear, soon to be 4.5" coils up front, 3" leafs w/ 1.5" shackles out back. I can't jack up the Jeep where I normally would because the kit requires access to the frame rail from the control arm mount all the way back to the cross member. I can jack...

XJ '91 4 door 4.0, AW4, Dana 30 / Ford 8.8. I am ready to buy a locker for my front axle. I have settled on an Eaton e-locker but it appears there are 2 possible models: Eaton 19818-010 and EATON 19818-020. Summit is out of stock on both and says that 19818-010 is no longer available. Amazon...

'87 MJ 2wd trim level unknown (posting here for visibility and because it should be the same) I am trying to get this connector disconnected: Will not budge and not sure how to get it apart. Connectors are the most frustrating part of working on vehicles! Need to get this out to help clear...

1987 MJ, Short Bed, 2wd, no drivetrain atm. Can I install any XJ/MJ front end lift on a 2wd MJ? Background: I've had this poor Comanche sitting since 2009 so I suppose its time to start working on it. I've kicked off a 5.3 V8 swap and apparently I need to lift this thing 3" before mounting the...

Hi, I'm preparing to swap an 8.8 into my 91 XJ so I bought the Ruff Stuff 8.8 kit. I mocked them up but the spring perches don't fit down onto the axle tubes because they have little protrusions. Without those, they look like they would fit great. What am I missing? Should I grind them off? I...

1997 XJ Cherokee 2wd, 2dr, 4 banger, 5 speed manual, Searched but couldn't find anywhere blah blah. I cannot find the air conditioner evaporator drain anywhere. I've read that its above a frame rail and I've also read that it is inside the frame but not sure I believe that because it doesn't...

91 Laredo i6 aw4 np231 I took my dash apart this weekend and now I can't remember where this ground wire connects to the headlight switch. I took a pic of what I'm trying to figure out. My dome light does not turn on when you rotate the switch and hear the click. I'm pretty sure that is...

91' Laredo 4.0, np231, aw4, its a heap. Replace the fuse, and the blower fan will work for for a minute or so, then it will blow again. I ran the fan directly off the battery through a 25 amp fuse and it did not blow that fuse so I'm pretty sure the motor works correctly. I have all speeds...

Looking to switch out the gears in my '91 XJ's front axle. I already have a carrier and lockright so I am just looking for the gears. Let me know if anyone is looking to part with a set. Thanks.

I let my account lapse (having a kid = no time!). I want to renew now though. Do I renew as a new membership or membership renewal?

Housekeeping first: Vehicle: 87 shortbed MJ 2wd, 2.5L throttlebody FI, 4 speed manual (AX4?). Drivetrain I'm think about swapping in: '90 4.0L, 5 speed manual (AX5?), NP 231 t-case. Basically, what I want to know is what do I need to watch out for because I've done my fair share of wrenching...

My business has a big insulated enclosed shop roughly 80'x50'. We have 4 HVAC units heating and cooling the space all on their own thermostats. Anytime the season changes, or someone changes one, they get all out of whack. So, I would like to control all the units with one thermostat or maybe...

Hello XJ folk, '91, 4.0, aw4, np231. I have been chasing poor gas mileage and low power issues. I was looking at my charcoal filter cannister thing that is close to the firewall on the passenger side an I wasn't sure if there was supposed be hoses connected to all the ports because it looks like...

I believe this is a carrier for a dana 35 with 3.55 gears. I did a quick search but couldn't find the necessary information to confirm this. Pay the shipping for this thing or come get it and its yours. Comes with some spider gears. PM me for s shipping quote.

I am looking to buy a TJ Moab wheel for a spare to match the rest of my wheels. It needs to be the 16" with 5 on 4.5 bolt spacing. Thanks

Has anyone ever used one of these? http://www.summitracing.com/parts/CLK-GE2036/ I'm looking for something that can brake something 21" wide and 12 gauge and inexpensive. Everything I have found is either >$5k or can only do 22 gauge thicknesses. I'd love to buy this thing and try it out but I...

'91, 4.0, aw4, np231. My Jeep runs too cold, usually on the second strike of the gauge which is around 150-160°. This has been confirmed with a IR thermometer so I'm pretty sure my gauge is functioning properly. I've been through 3 thermostats and am currently running a mopar 195° purchased...

Ok, '91,4.0, aw4, np231. I was working on wiring up a new harness for my H4 upgrade insert when I accidentally shorted the positive terminal to the hood latch. Now there is a nice burnt mark on the hood latch and when the key is in the accessory position nothing happens, it will not crank and...

I am looking for a set of 4.10:1 gears for the front axle of my '91. It has a high pinion vacuum disconnect dana 30. Swapping in an 8.8 with 4.10s out back and I need the gears up front to match.

I believe these are stock gears from an XJ. 3.73:1 ratio out of a D30 front axle. Pay for the ride and they are yours. PM me for a shipping quote. Otherwise they're going in the scrap heap.