Search results

5-90 : ! Thanks for the Intro. ! 90PioSport99 : I'm on page 5 of your 34 pages of threads - Primo Site. I'll find a 7120 '93 head somewhere for this 1982 Eagle 2dr. Sedan project. Bouncy : I'll research the...

My Dad was the Principal of our High School here in NY. We lost more parts - got parts 'switched' - and had jobs botched then I care to remember. Buy a Factory Tech Manual for your vehicle & accumulate tools - much better.

No, you can't run the dual exhaust headers on earlier heads unless you use an adapter: http://www.naxja.org/forum/showthread.php?t=919384

I've a 2000 TB / Intake to 1988 Renix XJ. What mods can be done to get this to work properly ? :phone:

I don't count lock failure as Cranes' Cam fault - AMC locks are notorious for failing - gear failure is indicative of cam walk - which is why MoPar installed the cam buttons in later production. Crane gave you a free cam ? and you gripe... I've dealt with Crane since the mid 1970s - top...

At this time I've a Pro Custom Cam Business that is creating the rough cores looking at the stock cams - then CRANE will receive them - turn them into finished product according to each orders specs for a tentative $500.00 - custom cam pricing. CRANE AMC hydraulic roller lifters with a special...

It is time for a lube change - Royal Purple G3 ? I'm in New York so it's a cold weather set up. According to one site - the '97 - '99 AX15 is the one to look for - High Output versions - has beefier input shaft. Now to start surfin' for info on the R154 Supra Turbo trans. & the differences...

No - I don't beat my rides - building an AMC Eagle Kammback for cruising. Engine is a '78 360 - cam'd for Torque & nice rumblie sounds. I've an '89 Cherokee 5spd. DD - I find 1st to 2nd is 'truckish' - don't know a damn about std. transmissions mods - nice trans. tho - would be A-1 if it...

Re: 5.4 engine swap ?? 31" / 32" rocker box edge to edge for a 5.4 engine. At the very least - you'd need to tie the block down with a Torque Strap device of some sorts.

I'm near Rte. Interstate 84 - Newburgh Ny - Hudson Valley. Is the 2wd AX15 still available ? thanks in Advance !

I'm down - injuries in New York - seeking a healthy 2wd AX-15 & Bell housing - a helpful 'drop in' and go - bed / chair for the next 2 years - dream machine leaking 998 no longer operable & I have a pedal assembly / flywheel / std. crossmember - and chum 'Terry the Wrench' to see this...

I'm down - injuries in New York - seeking a healthy 2wd AX-15 & Bell housing - a helpful 'drop in' and go - runner leaking 998 no longer operable & I have pedal assembly / flywheel / std. crossmember. way Appreciated !

can i test an Attatchments ?

4.0 weighs 483lbs / 3.25" stroke / 85 or 90mm bore 4.7 is 82 lbs. heavier / better breathing heads / 3.33" stroke / 91mm bore iron 4 bolt block - same platform Toyota went F-1 racing with. Wiring in the ECM is the pita - major. Both have very skinny con rods - no Turbo / Supercharging over...

=You're Starting with the Wrong Engine= You're starting with the wrong Lexus / Toyota Engine: The 1 UZ FE rods are junk - as are most all the Toyota / Lexus engines. Plan on a set of MANLEY con rods and some Forged Pistons - like CP or Venolia - with a 'Turbo' ring paak. The crank of...

http://autos.groups.yahoo.com/group/strokers/ We're arranging for Roller Camshafts for the 4.0. Not cheap. Anyone interested - log on.

GET another block. Find a shortblock from a '97 or newer that has the factory 'girdle' for strength - the blocks are stronger too. You can get these pretty cheaply - then have your .030 pistons installed. Have you joined strokers @ yahoogroups.com yet ...

Check this "Intelligent Intercooler Spray" system: http://tinyurl.com/2u8s5j You can run safely, - somewhat - , 6lbs.boost on cast pistons and powder rods. Here is what you should use in that project. Use a T3 .63 a/r turbine and .50 T04E hybrid compressor. Less lag yet it can support...

Anyone familiar with the processes needed to make the AX-15 a 'quick-shift' transmission? I'd read something about 'under-cutting' 'dogs' ? Quicker / Smoother shifting is the goal.

need a '91 - '96 Instrument Gauge Cluster - nice shape - inexpensively ? I'm in New York: 12561 thanks in Advance ! Bt