Search results

1998 classic, 4.0, AW4 So, while I was out wheeling a couple weeks ago, I got stuck in a mud hole and ended up overheating. The temp. gauge was pegged and the engine started to smoke, I'm guessing from burning off some oil, etc. I shut it down after I got pulled out as it was pinging really...

I have a RockKrawler 3 link 6" long arm setup in front (with 2" extended bumpstops) and currently have shocks that are 27.5" extended and 15.5" collapsed. The ride height is 21.5", so right now I have 6" of extension and compression available. My shocks are the limiting factor in axle droop...

So, I just put in an auburn ected locker in my d30. I installed a diff cover from a low pinion d30 because it already had the electrical plug installed in it. My 98 is a high pinion d30. Well. After installing the cover, I noticed that the fill/drain plug is 1" lower than my high pinion cover...

I have a pair of almost new cross-drilled rotors I'm selling. I swapped in a set of TJ axles to cure some bad unit bearings, and I have to use TJ rotors now. These have maybe 500-600 miles on them, basically new. Worked great. Did improve my stopping from the regular rotors I had before...

Will TJ d30 axle shafts fit into the xj d30 housing without any issues? I have a 98 xj and I am installing an auburn ected locker, which came with the entire d30 axle assembly from an 06 tj. Since my unit bearings were questionable, I was going to just swap the axle shafts from the tj into my...

So, what are the causes of low voltage to the fuel pump? I searched but couldn't find anything for actual causes of it. The reason I ask is that I recently turned my jeep into a submarine and my fuel pump ended up dying for whatever reason as I was leaving the trail. Got towed home, put in a...

Alright, so I've searched and everything, just looking for some quick input. So, I have 98 xj, auto, 6" lift. It's been having a voltage issue for the past week or so where the voltmeter will drop to 0. I'm pretty sure it's just a bad battery cable as when I wiggle it around and tightened the...

Where have you found grease fittings that fit the Rock Krawler Monster Joints? They are 1/4"x20 threads and I can't find anyplace that has them!

I'm selling the leaf springs from my 98 cherokee. They are the stock packs with a Rubicon Express 3.5" add-a-leaf in them. Have worked great, I just upgraded, though. Haven't sagged. Only been on about 9 months, less than 1,000 miles. Flexed and rode very well. $50 and they're yours! Or, if...

So, I just picked up a set of RC 4.5" leaf springs and I want to split the pack to add in another leaf. The leaf spring clamps on it have some sort of bolt going through the bottom leaf only and the bolt has a round head. I haven't looked anymore into than that, but wanted to see if anybody has...

So, I just found a deal on some brand new RC 4.5" leaf springs. My goal is to get 6-6.5" of lift in the rear. I am using revolver shackles, which supposedly don't add any lift (I know some people hate them and some love them, please spare the flaming on those, I got a good deal and want to...

So, I just recharged my a/c because it wasn't working lately, and come to find out the temperature knob is broken and stuck on heat! When I turn it to cold, it clicks and pops, but does not change the temp. setting. I haven't had time to take the dash apart and look at it, but is this an...

I have a pair of Rough Country 1.5"-2" lift shackles that are basically brand new. I installed them about a month ago and the jeep has just sat there as I've been installing a long arm kit. So, the shackles have been on the street maybe 50 miles since installed. I decided to go another route...

So, just recently my voltage guage started going out on me. It will come back on once in awhile, but is at zero most of the time with the check guages light on. When it does come back it only shows about 9 Volts. I haven't tested the alternator yet and wanted to get some input before I pull...

I currently have a RE 3.5" AAL and RC 2" shackle in the rear, putting me at 5.5" in the rear. My front is at 6.5" though. I was going to add another leaf in the pack to get that extra inch. I was thinking of using the main or second leaf from an XJ pack or S10 pack. Do you guys think this will...

Is anybody running the Rock Krawler 3-Link Long Arm setup? I recently installed one (I bought it used) and am trying to adjust everything properly. The instructions say to set the lower arms at 27.75" and the upper at 30". Well, the lower arms are 28" with the joints threaded all the way in...

So, I just installed a 6" long arm lift on my 98 xj, 4.0, Auto. When driving it, at any speed, it makes a harsh, loud growling noise (best way I can explain it). It sounds like something is grinding that shouldn't be. It's definitely coming from the front. I tried removing the front driveshat...

Is a TJ drag link interchangeable with an xj? I have a 98 xj and have an 06 drag link I want to put in. The reason I want to swap it is because I am putting in a drop pitman arm and a steering stabilizer and the stabilizer is already attached to the tj drag link, so I figured it would be easier...

I have a set of (4) slightly used Pro Comp ES3000 shocks for 3.5" lift with red boots. They are only 9 months old with less than 1,000 miles on them. I have taken the Jeep out maybe once a month over these past 9 months, so that's how (un)used they are! They are in great shape (maybe a little...

So, I was taking out the driver side upper control arm axle mount bushing for my new long arm setup. To get the metal sleeve out, I took a sawzall and cut the sleeve on both sides so I could collapse it and get it out. Well, of course I ended up cutting into the mount itself prob. 1/4 way...