Search results

hey guys thinking about buying trail gears hi flow pump, just wondering if anyone can measure the exact size of the hole on the pulley, I may be able to press my factory xj pulley on this pump. Thanks!

hey guys. i recently ran all new brake lines on my xj, and when i attempted to bleed the system., i had some problems. i started with the rear first, and they both bled good, with lots of fluid coming out then i went onto the front and they both arent bleeding at all i removed the line...

OK, basically i cant afford (right now) crossover steering on my front d44, and the leaves are in the way of normally mounting the draglink to the tie rod. what i have planned in my head is to custom build out of heim joints, a draglink and tie rod. the draglink will be about 1 and 1/2 inch...

thanks for the tip, but im just going to do a square front driveshaft.

im sorry, i searched and found my own answer, it turns out i have about 6 inches of lift or so i guess thats going to have to do, sure looks like im going ot have to lengthen my front driveshaft to reach it, maybe im wrong tho.

On my XJ i was wondering how much lift i got, well i measured at ride height i get 12.5 inches from the top of the axle tube to the bottom of the uni frame rail directly above it, at ride height. (the front axle) i built my own diffs, and went with front leafs and am now worried i got TOO much...

On my 1992 xj 4.0 high output, i was just wondering if an ac compressor would fit from a jeep thats either a 1997 or a 1998.

i am going from where my bumper is to the entire rear of my jeep of course along the straight sides it will be 1 solid piece, but where the rear fender well is, the uni rail goes up and curves a bit also, and it was at that spot that i would put a new piece on and fishplate overtop both...

is it important to have your frame stiffeners all 1 continuous piece all bent up to fit the rails, or could you section them. what i planned on doing was using as much as i could, and where it bends up, cut a piece and weld it in. then overtop of both plates, fishplate it. to me it seems a...

just wondering how they give a harder pedal feel, whats the difference if they both dont expand under pressure?

someone please correct me if im wrong but i remember reading somewhere that using anything other then normal steel brake lines, will give the brake pedal a softer, spongy feeling. this is because the insides of the stainless steel brake lines are able to flex and expand, and then your brake...

if i so choose to do so, will a need a trackbar? whats the purpose of it if the rear does not have one?

if its a gm then the front axle is a passenger side drop and wont work with your xj youll have to look at ford or international harvester front ends for drivers side drop preferably early to mid 70's ford f250/f350's./

ok, what diffs are possible to get on a 1987 FORD 3/4 TON 4x4. im going to swap them into my xj, the guy lives an hour away and i want to know what diffs they are.

i live in edmonton alberta where it was -37 degrees celcius a day ago, and my 33 ltb's had insane flat spot for about 2 km's, after that, it was smooth sailing from then on out. i use airsoft bb's to balance as well, and i comfortably drive at 120km/h with no vibs.

ok, trouble codes 22** ECT Sensor Voltage Too High (or Too Low) Engine coolant temperature sensor input above the maximum (or below the minimum) acceptable voltage and 51** Fuel System Lean A lean air/fuel mixture has been indicated by an abnormally rich correction factor Im looking to buy...

thanks for the replys if the front clip needs to be redesigned then its not worth it for me to do this at all, ill just have to scrounge up something with the 4.0. thanks

just wondering if anyone has any info regarding this swap. I found a nice jeep body, an 86 xj, with the 2.5 inline 4. I want to swap my 92 ho inline 6 into it along with my tranny tcase, diffs and lift. So, just wondering if they motor mounts are the same, the firewall is the same, front...

thanks man, i appreciate it a lot. IM thinking of just going straight across with sheet metal, tieing it into my front bumper/brush bar, and then tieing it into my tube fenders as well. Then ill just have to find some sort of real good driving lights, that will have a mount on them or...

im loving the looks of it, i made my own tube fenders on my rig, and now i had to remove the front clip as well, because there is nothing to tie into to keep it secure now (my fenders are completly removed.) So, i was wondering how u attached the front sheet metal for your headlights, and...