Search results

I currently have 2 running and driving XJ's...An 88' and a 91'. I also have 2 XJ's for parts. a 96' and a 89'. I'm am working on the 88' as it has fewer problems than the 91'. I have a question as to ordering a factory manual that would cover all of them from Pacific Coast Manuals. Is there a...

So, is there now a exhaust manifold for the older ones with the egr bung? http://www.ineedparts.com/index.php?dispatch=products.view&product_id=1336 Or have they always had this one listed?

Back in April 2010 I was having a start no start issue with my 88 Jeep Pioneer. 88, 4.0, auto, 4x4 The first test showed the CPS to be out of range...replaced it....fixed the problem. Then the problem of the start no start issue came up again a month later...the CPS showed to be fine...

2000 XJ, 4.0, AT, with factory security alarm. reaper1972 pulled into my driveway last night and just before he stopped to park in the driveway his jeep died. It will run on starting fluid…. He put a new fuel pump on it sometime since February. I’m going this morning to pick up a fuel...

1988 Jeep Cherokee 4.0, I6, Auto Trans, 4X4 Trying to diagnose a no start problem. All grounds are good and battery is strong....... At times the Jeep will start and run fine for about 5 mins or so then shut down. After a bit it will restart.....sometimes 10 to 15 mins....sometimes not for...

I'm planning on building my own front bumper and flat towing the rig. I plan on using the tabs on the bumper for the flat towing. Where do some of you that flat tow attatch the safety chains to the towed rig since the tabs on the bumper are the main connecting point to the tow bar? I'm...

The PNP near me is having a anything you can carry out sale for $60 bucks. I have a 88 Cherokee I6, D-30-35, automatic with 231 TC. If I find a non disco axel ...will my drive shaft still work?

Ok, I have a question about it. All other sensors checked good as I have posted in my MAT thread. Replaced: MAT sensor New o2 sensor MAP checks out ok No sign of exhaust leaks TPS checks ot ok ...vehicle shifts fine.... IAC was tested with a IAC tester and showed to work. But would not bring...

88 XJ 4.0 Auto 4X4 Trying to run down a high idle issue. My MAT sensor is dead ...no ohms even when put in boiling water to test. Will that cause my high idle problem? No vacuum leaks ...verified by smoke test. TPS is within specs. Coolant sensor is within specs. Map sensor is good. Haven't...

I know most of the trouble shooting as to what to look for.....but I can't find the answer to this question. 88 Jeep Cherokee auto I6 4.0. There are three vacuum lines to the axle shifter. Yellow....white....green. With Jeep in 4WD and running and in Park, should I vave vacuum to all three...

I noticed that some of the other chapters have The Official CL Thread... Is there one for the RRC? I think it might be a good idea to have one here as apposed to starting a new thread every time we find something on CL. :compwork: Maybe make it a sticky so it won't get lost in the...

Not mine Could be a good deal.....for someone......maybe and I did say "MAYBE":eyes: 2001 XJ that needs a front axle assembly http://austin.craigslist.org/cto/1060146265.html

http://houston.craigslist.org/cto/1057178726.html

I have searched and I guess I haven't hit on the correct "searchwords" yet. Those of you that have made the 3" lift bastard pack (regardless from where your leafs come from....S10...Dakota or whatever) using the XJ main....what did your shackle angle come out like? Was it OK ...or will it...

I have a question that I have not found an answer to regarding spring measurements. Looking at the General Spring link .... I know that the stock spring measurements are 23 x 28 5/8. Using the same measuring formula as the site...

My daughter has a 2007 Jeep JK 4 door. They did a lift on it and she has the coils and rear springs left over. Will the front coil springs work on the Jeep Cherokee? I know the ZJ coil springs will work as to building a Bastard Pack setup. If so .... will it give it any lift? I’m...

I've been reading the post for trouble shooting this bugger and I have a question. I just went and checked the vacumn actuator motor on the front axel and..... Is it supposed to move or should it be ridgid? I was checking the hoses and it turned just a little. My 4wd works good .... just...

For those who have done the lever replacement..... Can the plug at the end of the wire be fished down without cutting the plug off? 88 Cherokee Pioneer

I'm going to tag along with my son to the the local PNP tommorrow. He's going to look for a part for his SUV. I've only been to this PNP one time .... about 6 month ago. I have a question about finding a lifted Jeep Cherokee. The vehicles they have in their yard have all had their tires and...

I repaired an ill fixed (by someone else) vacuum line to the Map sensor located on the firewall. The plastic line had been broken at some point and a rubber line was slipped over it (connecting the two ends together). The inside diameter of the old rubber line was too big so I replaced it (...