Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Welcome to the new NAXJA Forum!
If your password does not work, please use "Forgot your password?" link on the log-in page.
Please feel free to reach out to [email protected] if we can provide any assistance.
Hi all,
I'm looking for a sanity check on a plan here. The TREs on the Currectlync setup that I've had on my woods beater for the past few years have gotten worked out and there's a ton of slop in my steering anymore. I'm planning to rebuild the front-end to get some additional down-travel and...
I bought the Teraflex high-steer knuckle for my front D44 (I do not want WJ knuckles--nothing wrong with that, but I am going a different place). I am trying to layout the steering links.
Right now the upper arm runs smack into the swaybar link hardware that I put in for OTK tie rod. So those...
I'm planning to replace the timing chain on my pos in a couple of weeks and looking for tips. The last time I did this (years ago) the motor was on a stand, this time doing it while the motor is still installed. Do I need to pull the radiator? Anything special about the gap between the timing...
Thinking about switching the (unofficial) FB group to private. Downside to being a public group is everybody sees what you post (notified in some cases), which limits participation a bit. The group was created as public so that events could be shared, but if the events are created on the...
Anybody here have wiring diagrams for 97+ and willing to look up wire colors for the rear wiper and washer circuits? Neither of mine work, switch is putting voltage through the fuse, want to check the wires in the cargo panel that's already off before diving into the motor
I picked up another XJ recently, plan to use it for backup DD / winter driver. I am trying to get some stuff fixed so I can take it through MD inspection. The big thing is the ABS light is always on.
I borrowed a friend's Snap-On MT2500 with a universal cartridge (he's a Ford master tech) and...
Looking to replace the ignition key cylinder in my steering column (worn out--key falls out on big bumps) and looking for experience / options. Can a locksmith cut a new cylinder to match my old key? Otherwise I would have to replace the door and hatch locks as well.
Its a 91 don't think its in...
I was looking for new R12 service valves to go on a new replacement compressor. Couldn't find anything anywhere. Got to talking to a 4 Seasons tech and we went through the catalog, lo there they are
Four Seasons parts 12721 and 12722
Available on Amazon pretty cheap as of right now
Gotta save some pennies for my next $$ upgrade and I can't quite decide between these three so I will ask the NAXJA family
Long arm upgrade -- I'm on 6" of lift with short arms. Doesn't bother me except downtravel is limited by the rotational arc. I get a tire off the ground all the time and my...
I have a 91 but my HVAC system is bits and pieces of custom parts. I currently have it drained for a heater core swap. I was looking at ways to simplify it a bit and came across this page in the parts catalog. full size
Is that an accurate diagram for 96? Earlier models all had service...
My 91 parts catalog shows the heater core / evap core foam seal as part number 56006312. I can't find this anywhere.
The 01 parts catalog shows a multi-part seal "kit" part number 4874069AB which seems to be in production and available.
Are they interchangeable?
Anybody have a meat thermometer they can stick in the radiator near the outlet to the water pump? What temperature are you seeing after engine has warmed up? and what is the ambient temperature?
I have radiator inlet temp of 240 max dropping down to 100 at the outlet, so radiator is shedding...
Any of you with an infrared gun willing to take oil pan temps?
My passenger side seems to run about 180, but the driver side next to the downpipe is 220ish
I have those adjustable JKS short arms, love them and their freedom of movement. I am thinking about converting them into long arms by extending the tube. What kind of problems am I looking at?
Bought an AW4 from a guy today, had this tangled in with the other harnesses. Its a TPS connector on one end, for sure. Never seen one standalone before--always seen the TPS wire bundled in with the other sensors and gizmos. What is it used for?