Search results

Good for a laugh. Why do people do this? http://roseburg.craigslist.org/cto/1462349087.html

I was at the jy today and spotted this hood. I found out it fits a 1988 thunderbird turbo coupe 4 cyl. I think the scoops are neat, and the sealed "plenum" may even be useful for true cold air intake. More focused on venting underhood heat though. What do you guys think? I'll add pics later, my...

I am looking at buying a camcorder for family stuff, trail runs, riding trips and other random stuff. I have all but decided to get a flash memory version, and am seriously considering the canon fs10. It's essentially the same as the less expensive fs100, but has 8G internal memory. Anybody have...

Hey guys, I am curious if anybody has done their own hack/tap using random parts on a pre 96 np231? I have seen the info about what yokes will work, and I'm all fine and dandy about that, but what about the seal housing like comes with the RE1801 kit from RE? It is the part in the center of the...

I know it's been covered and I'm hasta but it's difficult to get a clean search for 8.8 stuff since it's not a long enough search term. I end up with "88 xj wiring woes" and that sort of thing. I am seriously considering doing the swap, but having a hard time finding what I think is a good deal...

Check your local NAPA, but the one I work at is selling Herculiner roll on bedliner kits for $69.99! They will also give you a $25 mail in rebate! That makes it 44.99, which is just about half of what it normally sells for! Hope someone can save some $ here.:clap:

DRILL PRESS: A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, denting the freshly-painted vertical stabilizer which you had carefully set in the corner where nothing could get to...

Well, anybody going? I have been the last two years, and will be going again this year. It's the 26th of April. Lots of fun if you are into that sort of thing.:wave:

Do you guys ever look back at your Jeep as you walk into the store. Ever pull into the driveway in the family sedan and smile as your Jeep meets your eye? I have this habit, every time I pull in the drive with my wife in her car, I say "Thats a nice looking Jeep right there, who's the lucky...

I know, it's been discussed lots, but I haven't found any info specifically on what I want to do. I would very much like to mount a York on my factory AC bracket. It appears that I will have to move the battery, but I want to know if anybody has done it or not. I don't have the original pump...

I have been lurking the NW chapter for a while, but haven't seen any members in the Roseburg area at all. I have seen some nice XJ's around, but none that are in the local rig directory. Anyway, just wondering, would like to drink some beers with someone local who likes XJ's as much as me.:thumbup:

Scratching my head a bit here... Short pinion D30??? http://cgi.ebay.com/ebaymotors/Yukon-Ring-Pinion-Gears-Dana-30-Short-4-56-R-P-NIB_W0QQcmdZViewItemQQcategoryZ33728QQihZ022QQitemZ350004079968QQrdZ1QQsspagenameZWDVW

Can any of y'all tell me why this wouldn't work for a hitch mounted recovery shackle? Of course this is only part of the equation, but it seems like most of you guys use the threaded pin versions. http://www.napaonline.com/NOLViewer/Pages/Detail.aspx?R=99673&ShowPics=1

I have been reading and reading about front bumpers and tow hooks so that I am blue in the face now. I was starting to think it was time to plan a HD bumper with heavy multi-bolt mounts, extending through the front of the bumper so I could put shackles on. Then I looked at TONS of bumpers and...

So I decided to build my own LCA's, and didn't think I needed to worry about incorporating a curve like the Rusty's type. I was wrong. The diameter of my tube is 1.625. The problem is, the droop is limited by the LCA contacting the axle. The clearance is better than stock, but not good enough. I...

So I'm thinking about these wheels, MKW model M29. http://www.pacwheel.com/wheels.php?view=details&wheel=1090&q=45 I was wondering if anybody else runs them, and if anybody had a pic. I was planning on a 17x8 with a 265/70/17, (about 32x11.5) Opinions welcomed.

I am planning a budget/custom homebrew lift for my 85 XJ, and am planning on building a set of LCA's, possibly UCA's if I see a need for them. After much reading I have decided it would be best to do it with some Johnny joints rather than the previously planned stock rubber bushings and round...

I have done a lot of reading about this subject, and really appreciate all of the write-ups. It looks like I will be able to build a lift for much cheaper than buying a full setup. I have decent welding/wrenching skills, and am ready to tackle a project. I was planning on doing a S-10 pack, but...