Search results

Hey Guys, I've searched some what I'm having trouble finding a clear answer to my question. I did a KJ rear disc brake swap on my 99 XJ (8.25). I used the XJ front wheel studs on the rear for this swap. My question is if I have enough wheel stud/lug nut thread engagement for off roading...

I'm finishing a small build on a 99 XJ and have some parts left over. - 3.5" front coil springs, I believe Rubicon express - $75 - NP231 I took out of a 99 XJ. Still stock with a slip yoke (paint blue for some reason....) $100 obo - Tuff Country lower control arms, bushings are...

I'm selling my XJ so all my parts are going too. I have the following - tube fenders (Just the pre bent tubes) from JeepTubes. Front and rear. $180 - Blue Torch fab 8.25 DIY diff cover (Still needs to be welded) $40 - I have some Ohana Fab sliders (.120 wall 2x2). I started to modify one of...

I have four almost new (About 300 miles and one short trail run on them) 37x12.50x16 Maxxis Creepy Crawlers. We bought a new JK and I want to run 35s on it so I'd like to trade these for some 35's or sell them outright. I can provide picture of the condition of the tires if you want. These...

I have a T-MAX EWI-10000 winch that has never been installed! It's still new in the box with cable. I got rid of the project I was saving it for so this needs to go too. The specs can be found here...

So I finished my build and took my XJ out for a test drive. On the test drive my buddies and I ran a few miles down the road to a natural gas well site. (Basically some dirt to test things out in) Ran it through 2WD and 4HI with the front locker engaged and disengaged. Everything seemed to be...

I've upgraded so some used parts need to go... Rustys 4.5" lift xj springs - $80 Rocky road lift shackles 1.5" lift ( 6" eye to eye ) -$45 Skyjacker single flex upper and lower control arms with new bushings ( needs new heims ) - $215 Metal moto 16" rims 5x4.5 and 9" wide alloy rims ( four of...

I'm looking for high pinion Dana 44 26 spline 1350 series yoke. I'd like to have my front and rear axles have the same size ujoint. PM me if you have something and let me know what you want for it. Thanks, Lurch

Had these up for sale a little while ago and the sale I had lined up fell through, so here they are again. Both axles are out of the Jeep now. HP Dana 30 - 4.10 gears - 1995, so one piece passenger side shaft - decent brakes left on it. - open 8.25 - 2000 29 spline - 4.10 gears - Disc brake...

I'm upgrading my axles so these are for sale now. HP Dana 30 - 4.10 gears - 1995, so one piece passenger side shaft - decent brakes left on it. - open 8.25 - 2000 29 spline - 4.10 gears - Disc brake upgrade. - open The HPD30 is out of the jeep, but 8.25 is in the jeep still. If a buy comes...

Have a set of 35" MTR style retreads on rims. (5x4.5) Thinking about going to 37s so I thought I'd see if there is interest in these. They have about 200 miles on the tires right now. $1100 obo Dave - 303-810-3927

5 285/75/16 Treadwright Warden ATs (BF Goodridge ATs) on 5 steel 16x7 5 on 4.5 rims. Four of them are used but have even tread wear, the fifth is brand new and hasn't even been on the ground, you can still see the flashing on the tread from the mold. I ran these on my Jeep around Colorado...

Hey guys, I thought since this is dealing with a Colorado part I would post this question here. I have a set of Ohana Fab sliders and I've seen Troy (and I think others) mention that they are a light duty slider. So I've been thinking of ways to beef them up. One way I've thought about doing...

My windshield was pitted really badly and I though "why not pop it out and fix the rust while I'm at it..." Well what I thought was surface rust turned into a bit more.... So now I'm thinking these are the steps to follow: 1) keep scrapping the rust out 2) cut out what's rusted through...

I have a 78 F250 rear dana 60 Full Floater with 3.55 gears in it. I was going to use it in my Cherokee but decided to go a different route. The only thing missing is the pinion nut. I can send pics. Asking $150obo Dave - 303-810-3927

I have a Ford 8.8 rear axle out of an explorer. It's a 1994 so it has drum brakes, but it has the 31 spline axle shafts. It's a open diff with 3.55 gears. I don't need it any more so come get it. $99 for it drum to drum. Dave - 303.810.3927

Stock 1994 Ford Explorer 8.8 Rear Axle. 3.55 gears Was going to use in a project but decided to go another way. 31 spline axle shafts, but drum brakes. $150 obo Dave 303-810-3927