Search results

OK, so I did something dumb. I pulled the yoke of my dana 30 to change the seal, but I did not mark the nut for re torquing. What should I do? Is there a spec I can go by or do I just try my luck and see what happens. Any help would be much appreciated. Thanks!

OK, I searched but with no luck 95 Cherokee Country currently running three inch lift that was pieced together. Front coils are crap and too soft. No winch,YET.. If I order Rusty's front 3" should I go standard or hd? Thanks!

I have a 1994 Cherokee that I need to sell. It has 126' on the clock and runs great. 3" rusty's lift 31" BFG All terrain's (5) Swing Tire Carrier Front Tow points Pop up Sunroof (does not leak) Rhino linned rear cargo area Alpine system w/ 6 cd changer and outboard amp with 12" custom sub...

I have a 1994 Cherokee that I need to sell. It has 126' on the clock and runs great. 3" rusty's lift 31" BFG All terrain's (5) Swing Tire Carrier Front Tow points Pop up Sunroof (does not leak) Rhino linned rear cargo area Alpine system w/ 6 cd changer and outboard amp with 12" custom sub...

So I went to a u pull it yard today and found A old jeep Pioneer cherokee. Anyhow, I got a set of front tow hooks and brackets and a stock rear tire carrier for a whopping 30 bucks. Anyhow, as I am looking into this tire carrier, what is the trick to reinforcing it well enoughit can handle a...

OK, I am not mad at the tranny by any means. This is solely my fault. The other day I was driving up a steep hill and noticed smoke behind me. Got out and looked underneath. ATF all over. Checked the dipstick, it had fluid but it was milky. So to make a long story short beep me... Turns...

Well basically the title says it all. My jeep is overheating badly, and only blowing warm under load. My conc, tstat. So I bought one from mopar, went to put it on and the upper bolt is litterally seized in place. I tried a over-under combination on it but don't want it to snap inside of the...

A major topic at the last meeting of the Red Rock 4 Wheelers was the status of the 5 year permit and what is happening. Dave Adams our present Land Use Officer and Jeff Stevens, former vice president of the club gave us an up date and it is at best alarming. The Environmental Assessment (EA)...

OK, so here's the problem. My 94 country with a I6 and aw4 tranny has had a hard time starting recently. At first it catches, but then just continues to crank. As soon as I press the gas pedal it will start. hmm Also, once I am driving and come to a stop, it idles around 2k for maybe 5 secs...

I feel kinda stupid by putting this as a new thread, but I am making some brackets to drop my sway bar. I was hoping someone could tell me the pitch and length of the bolts I will need. The only reason I ask is bc it's my only car, and once i get it apart I can't get anywhere. Thanks in...

Hey guys. Right now i am trying to fix the rear end of my moms gc. Tried jeepforum but know one helped. Anyhow. It had a droning noise coming from what seemed the right side. Took the diff cover off and the top and bottom pinion gears have symetrical chunks outta them. Are they supposed...

Just a wuickie. Does anyone know if theres a difference in length for a 4dr and 2 dr version? This is the shaft that connects from the firewall to the steering box. TIA

OK, here's the deal. I need to figure out which color wires on the back of the switch go where. The old one burnt up and my brilliant ass cut and LOST the plug. Help! thanks guys

OK, so here's the deal. I made a homebrew 3/4 drop for my tc. Now here's the problem. Both studs came out fine, the passenger bolt came out, but the drivers side bolt snapped , and it didn't take a lot. So I drilled, and I tapped, but when I did I don't think I went through straight. The...

I know, I know, there have been a ton of write up's for this kinda thing. BUt here's my question, do you think the wall diamter of the 1" tubing matters? Do you think I can use 1/16 and be ok? There was a write up previously and he used 1/8, but wish he had used 3/16. What do you guys think???

OK, so I know how 3" of lift thanks to rusty's lift. When doing it, I snapped both sway bar links and now I float on the highway. I went down to advance today and picked some new one's up. $45.00. Anyhow, am I better off with stock or quick disco's on a dd? Is one stiffer than the other...

I just installed a 3" lift and I have some small vibes? Is it safe to drive like this on the highway? at least temporarily?

has anyone ever had the lower track bar bushing sieze to the bolt? If so how did you break it free? I can't get anything on the sleave to hold it. :hang: Thanks for your help

I hope I get a litlle bit of feedback on this thread. I just bought a cd radio, and now I need to get an antenna for it. My questions are, what kind do I get, whip or roof, and any preference on brand? It's gonna be used for some highway driving, and also trail riding.

I know that this is a little of the modified area, but I know that it will grab more attention in here. I am looking for a compressor that is realively portable but can still handle my impact (ir 2135), die grinder, air ratchet and possible a spray gun. It has to stay on a 110 line bc I rent...