Search results

I know im gonna get crucified for even asking this but right now I just dont have the time or the money to do a full rebuild. But can I put new main bearings and rod bearings by just dropping the pan? I need to know cause this is my daily driver and Im suffering from a loss of oil pressure...

My 90 xj recently sat for about 4 months. Now im driving it again. So I go get in it tonight turn the key and nothing happened no lights, radio, starter, dont recall if the fuel pump came on or not. Tried starting it in neutral and it didnt start right away. It rolled back a bit then I...

So I replace my shocks and as i was replacing them I broke one of the bolts off. So soaked the hole with penetrating oil for 3 days. So today I drilled the hole into the broken screw for the ez out. I put the ez out in a tap handle and twisted it into the hole and snap!!! SO now I have an ez...

i have a 1990 cherokee on 4.5in lift with 33's. So some how my rear axle shifted backward on the driver side causing my drive shaft to put out of the transfer case. The t case is a 231 and rear axle is a D35. When i crawled under the truck i noticed that the shock was busted at the mount...

people keep telling me that i need to regear my axles for larger tires. My question is do can I run 33's on stock gearing?

What are some symptoms of a torque converter that is about to crap out? What does it do, what does it not do? I think mine is about go but im not sure. Its a 94 motor, tranny and Tcase in a 90 xj.

What size are the vaccum lines in my 1990 laredo. I'd like to replace all of them because It one more thing I an rule out as to crappy performance and because Im sure its all probrably 19 years old.

Can a ballast resistor suffer from thermal failure. My 1990 has an issue where the rpms creep up to around 1100 from 500 at idle. This only happens when the engine is hot. When it does creep up the minute I touch the gas it will stall or attempt to. When it does that if I remove my foot fast...

What do you guys think? My 1990 had and electrical issue that I thought was causing my truck to stall. We fix that problem and she ran great for a day. Then today I took her to the bank and and on the way back she stalled again. When she did stall I was at a traffic light and I could hear...

This is the second CPS ive put in in the last 2 months. The second of which went in a week ago. Well my 1990renix POS doesnt start again and theres no spark coming of the coil. The coil is brand new as well. So why or what is causing this? Both of the CPS's came from Advanced auto.

Where the heck is that is my asd relay located in my 1990 cherokee laredo?

I have this intermittant stalling issue that has got me stumped! I have a 90 renix with a 94 HO motor in it. The issue Im having is that when I slow down and reaccelerate she stalls. Ive already gone through grounds and cleaned them thoroughly. Ive thrown all kinds of money and replace just...

I just ordered a 4.5" lift from rusty's! Now my question is am I going to need UCA's as well? the kit comes with LCAs. At what lift height does the length of the UCA change?

Im suspecting my oil pump is about to take a dump. What are some other symptoms of an oil pump thats going to give up. Aside from the obvious one of a lack of pressure at the gauge. Right now as I drive around my pressure gauge never gets above 40. At idle it sits at about 20 and then...

What do I need to do to convert my old broken power aentenna to a fixed style one? Im sure ill need to remove the fender or is there an easier way?

Ok Im testing my ignition coil for my 1990 renix because I have have no spark coming off of it. To test it im supposed to set my multimeter to the highest ohm setting. Then put the positive lead to the positive post and it should read infinate resistance, correct? Well when I do that I get...

Ok my 1990 renix with my 94 HO swap has been running fine. I noticed I was getting poor fuel mileage. So my truck was running today with the hood open for an unrelated thing and I noticed fuel coming out of the fuel pressure regulator. It had recently been disconnected when I did my head gasket...

Does anyone have any recomendations as to free burning software?

My gas milage suffers. I get maybe 8-10 mpg. Im running pretty stock set up with only exception being 30x9.5x15 tires. All the sensors are pretty much new as well. That being said my temp gauge does flucuate from about 195 down to 150 and then it starts the climb back to 195. Im almost...

How interchangable are they? Can I use say grill and headlamp doors for a 1995 on my 1990? Im Just wondering because some of the pieces need to be replaced because they're cracked. I want the grill and everything to be black.