Search results

Just checking in to see if anyone has any experience using HPTuners on 99+ XJs? I'll be building a supercharged 4.0 at some point and was looking at options for tuning. I know of the Split Second setup but already own the HP MPVI2 and would prefer to flash the stock ECM depending on what all...

Long story short, my old XJ got totalled out by an illegal so I'm rebuilding from scratch. One of my main complaints with my old setup was the front axle. D30 tubes bend easy, and I had put 3 sets of gears in it over the years. I have another HP30 sitting here ready to build as well as a...

Like the title says, I'm looking for a good condition silver 97+ header panel and hood. The 01 I got to replace my 99 has some paint issues so I'd like to clean it up a bit if anyone has them. Thanks!

Hey ya'll, been a while since I was on the forum. Long story short an illegal totalled my 99 that I'd had for 16 years. Picked up a clean 2001 4.0 AW4 2wd with no motor to swap my drivetrain into. Donor carcass is a 99 4.0 AW4 231 w/ 120k. I have the 99 drivetrain pulled and cleaned up...

I've kinda been out of the internet XJ/forum scene for the past few years but I'm not seeing a lot of the names I used to back in the day, so I was wondering who still produces a decent rear quarter guard. I've been looking for a set to cover up some accrued carnage and I would prefer a set...

Looking to swap my low mileage 1999 drivetrain (4.0, AW4, 231) into a 2000 body with the same drivetrain. What all has to change to get everything to play nice? I know the coil pack vs. distributor is different so figuring the engine harness and computer has to move over, but what else changes...

Got a customer at my work looking for a 21 spline input gear for a 231 in the later gear cut or a whole case on the cheap ASAP. Any help is appreciated.

Looking for a good cond. AW4 for my 99. Seems I blew up my 1st/rev planet gears in mine. Thanks!

JCR full belly skid, includes complementary rock rash but no bending. Made from 1/4" steel, unlike the current production version which is apparently 3/16". Works with stock setup or a tcase drop. You will need new nutserts and bolts or self tapping bolts to secure the skid to the framerails...

Rubicon Express Super Flex control arms, includes all hardware. Need all 4 bushings replaced, flex joints feel good. $75 cash Located in Miton, GA.

Factory hard top off a Jeep CJ-7. Tan/brown color, good condition. Couple tiny paint chips, minor damage along bottom edge of driver side from sitting on the ground (can be seen just behind front corner of window). $350 OBO, located in Milton GA.

All off my '99 w/ 56k miles stock knuckles- $5 stock rotors- $5 two sets of front calipers, one set with decent pads, other with very good- $20/set master cylinder, unknown condition- $5 roof rack rails- $5 rear bumper&mounts, black & scratched- $5 stock front coils- $5 stock control arms- $5...

Will get pics up soon. Driver and passenger knuckles Akebono calipers w/pads Drilled rotors Stock drag link and tie rod w/TRE's $250 Located in Cumming, GA 30040

Since I recently bought a tow rig/DD I am now looking at a trailer to pull the XJ. The tow rig is an 05 Ram 5.9 QCLB and I am thinking an 18' trailer would give me the most versatility for the future. Storage and obviously price are issues so anything over 20' is definitely not going to work...

So I have this old 80's Ford 1210 3 cylinder diesel tractor that's been sitting on the property for around 8 years. I want to get the thing running but it has had fuel sitting in it since it was parked. No doubt the fuel is bad so I want to drain everything and prime it with fresh. Can I...

Selling a pair of Corbeau Baja SS supsension seats. Black vinyl sides and black cloth center. Also includes custom seat brackets for late model seat bases. Driver's seat has some tearing of the edging material from getting in and out. No stains. -$300 Located 20 min north of ATL, zip...

I am looking at buying a 97 ZJ with the 5.2, 150k on it. What should I look out for as far as common issues with these Jeeps? The axles and tcases I am familiar enough with, but not so much the V8/trans in them. Any help would be appreciated. Destroyer

Corbeau Baja SS Seats: Pair of Corbeau Baja SS suspension seats. Black vinyl sides w/ black cloth center. Will also include a set of custom seat brackets to mount them to late model seat bases if you want them. Driver's seat has some tearing of the edging material from getting in/out. A...

Heavy duty inverted Y steering: Gusseted TJ drag link and 1.5 x .25" DOM tie rod. Believed to be 3/4ton Dodge TRE's, match stock XJ taper. Drag link could use new dust boots. Tie rod nearly brand new. -$125 Garvin/Defender roof rack: 54x72" gutter mount, includes lockable spare tire...

So here's the deal- I did a WJ swap over the winter and ran it with stock steering for a while. Eventually relocated the track bar to utilize the higher steering arm of the WJ knuckle. Using Chevy TRE's I ran the drag link from the underside of the pitman to the topside of the WJ upper arm...