Search results

My jeep is a 92 XJ 4.0L ,5 speed. The jeep usually acts up when I'm going through some heavy mud, or hard rock crawling. If I keep the rpm up, it's usually fine, but if I get stuck or stop half way, trying to get going again is almost impossible. I'll let the clutch out and give it some...

Thanks for the reply guys.

I'm looking at getting a newer 4.0L for my 92xj. I have a line on a 99 4.0L with lo miles on it, will this motor bolt up or is there something I'm overlooking.

The guy I'm getting the gears from is telling me they are a thick set, and to drill out the holes on the carrier for the ring bolts and it should fit. Does this sound right?

Would a set of 4:10 R&P from the rear D44 of a Rubicon fit a D44 from an xj? I don't play with gears much to know better. I'm running 3:55 now with a 3" lift. The plan is to lift it this winter to 6" on 33's. I have 4:10's for the front already. I'm going to pick up the 4:10 R&P tomorrow for...

Re: 231 vent tube broken The vent tube is broken in the transfer case!

Wasent shure if I posted on the right forum

So i'm rebuilding my 231 and have this little problem! When i was removing the transfercase I noticed the vent tube was brocken and has been for a while. How do you remove the old piece from the case? I can get vise grips on it, and can even turn the piece a little but cant seem to pull it...

So i'm rebuilding my 231 and have this little problem! When i was removing the transfercase I noticed the vent tube was brocken and has been for a while. How do you remove the old piece from the case? I can get vise grips on it, and can even turn the piece a little but cant seem to pull it...

I'm instaling a aussie locker in my D44 rear axle, and ran into a snag with torking the ring gear blots. I have serched on line and for some reason, I'm reading some guys tork em at 80-90 ft lbs, and at the same time, someone els doing the same install on the same rearend will tell ya it's...

thanks for the responce. Would like to get it back together this weekend.

So i'm replacing the seals and shaft bearing when i noticed one of the old bearings on the shaft is backwards from the other one? When i puled the shafts out, one shaft came out ok ,the other one left the bearing race in the housing. So witch way is right and witch way is wrong?

Thanks for the info guys.

I wasent shure if you could put D B on at 4" or if you nead 6", also Witch company sels a good D B.

I have a 92 xj with a 4"lift I have just instaled I'm going to change the uca and the lca with R E adjustable control arms, and Im wondering if I should get drop brackets also?

I'm looking for a rear locker for my xj but not shure on what to go with? I'm thinking on an aussie locker for my 44. has any one ran one of these lockers in the winter?

I have a 92 xj with a 4" lift I'v instaled. I'm not shure If i nead to change the controle arms or not?, for a proper alingment. A friend of mine seems to think the stock armes will work, but i'm not convinced. I'm thinking of the R E adjustable control arms with the flex joint.

Thanks for the info guys.

Front axle has 3.55 in it (39-11) stampt on the ring gear. I bought a dana 44 last year and was told the gears are 3.55, but there actualy 3.54's(46-13)stampt on the ring gear. will this work ore do I have the wrong gears, and what should I do?

I tried unplugging the coolent sensor like my local mechanic told me, but found the vehicle emediatly runing through all the symptoms, and became totaly undrivable. I cleand out the throttle body and noticed some improvment but the symptoms are still there. I was toled from the local...