• Welcome to the new NAXJA Forum! If your password does not work, please use "Forgot your password?" link on the log-in page. Please feel free to reach out to [email protected] if we can provide any assistance.

Search results

  1. O

    HIDs and housings

    Just retrofit some projectors, its not that hard
  2. O

    Smittybilt suspension seats

    I ended up going with the corbeau XP's and couldn't be happier with the choice!
  3. O

    Oil Town XJ's 2 Door Build

    They've held up great! No issues yet Thanks! Attached to my BDS LA crossmember
  4. O

    Oil Town XJ's 2 Door Build

    Its been awhile since I've updated this thread. The Jeeps been parked all summer, as I've been too busy. When I wasn't working, I was at the lake all summer. I've started working on the Jeep again, I've ripped out my 1 ton inverted-t steering and I'm replacing it with a crossover setup. I hope...
  5. O

    otk tierod ball joint rollo!

    You will still have a dead spot with the spacer, but it will help a little bit
  6. O

    Steering help!!

    I'm so tired of my Ballistic one ton steering! I've been dd my cherokee and I've finally had enough of my questionable steering. The Jeep is aligned perfect and tracks straight until the tierods start rolling. I've tried different sized poly spacers to try and fix the dead spot, but they don't...
  7. O

    BFG Mud-terrain KM2 vs. Cooper Discoverer STT

    I went from stt's to KM2's and the KM2's are a much better tire in every condition!!
  8. O

    Project: HID Retrofit

    For anyone looking at ordering a kit from theretrofitsource.com stay away from there Morimoto bulbs and ballasts!!! It's been over 6 months since I did my retrofit and have had nothing, but problems with there bulbs and ballasts
  9. O

    building a front winch bumper. opinions needed!

    Here's how I mounted mine, I wanted the bumper to stick out a couple inches to protect the lights I'm mounting on the front of the bumper.
  10. O

    Help, want flares but PO did terrible hackin!

    Run 4 rear TJ flares
  11. O

    2DIN deck install in a 97

    Ya it was pretty easy to figure out what needed to be done when I physically tried to fit the receiver in there. The install went pretty well, all wiring was harder then actually fitting the receiver.
  12. O

    2DIN deck install in a 97

    Thanks, it was worth the wait:D There's install pictures in my build thread
  13. O

    Worth $450?

    I've order alot for northridge lately and have never had any issue's
  14. O

    Have You Seen an Uglier Bumper?!?!

    At least he color matched it okay, hahaha. He also was talking about selling these fenders
  15. O

    Oil Town XJ's 2 Door Build

    Its a factory dash panel modified by P1atinum http://www.naxja.org/forum/showthread.php?t=1024604
  16. O

    Have You Seen an Uglier Bumper?!?!

    His newest creation, some super clean tube flares. They look factory! http://www.cherokeeforum.com/f58/started-tube-flairs-today-51073/index3/
  17. O

    Oil Town XJ's 2 Door Build

    It should hold up fine, the surround doesn't support it.
  18. O

    2DIN deck install in a 97

    Just finished installing my P1atinum console!
  19. O

    Oil Town XJ's 2 Door Build

    I tried out my Alberta backroads topo sd card and it works perfect
  20. O

    Oil Town XJ's 2 Door Build

    A little work is required for a double din receiver to actual fit behind the console. First you need to remove the brace underneath the heater vents, I used an air saw and a dremel to remove it. You can see in the picture where I had to cut After I cut it out I had to seal up were I cut...
Back
Top