Search results

Includes all sensors. Works great, ran it on my 1999 XJ Increases your throttle response

I currently have the rough country 4.5 inch series lift. The springs in the front are very stiff. I ws wondering if anyone knew of a good quality manufactured soft spring for the front of my XJ. I have stock bumpers and do not plan on putting anything on the front. It is also my Daily driver...

Like new, just took them off my jeep. Less than 1,000 miles. Comes with all the hardware. Located in Lansing, Michigan

Just wondering who is running this set-up. I have the Rough country 4.5 inch series x lift kit I purchased through Grimus (who by the way has been by far the absolute best customer service relation I have ever had) Anyways, I was installing my control arm drop brackets and realized my rough...

Hello everybody, I am in the market for a rack that will safely transport two mountain bikes on the top of my cherokee. I have the stock crossrails that came on my 99 from the factory. I really don't even know what I need. Suggestions on brands and ingenious ways of mounting are apprectiated...

I have seen numerous ways people have restrained there sway bar once discconected. I was looking under my XJ recently to look for ideas. Has anybody utilized the exisiting holes in the "frame rail ?? (not sure if that is the correct term)" I was thinking of just looping something through the...

I just finished up the install of a B&M super cooler with trans temp gauge with dual sending units on a toggle swich to moniter the trans temp going in to the trans and the fluid coming out of the trans. I will post up pics and results of tempeture. Keep posted!

I have a 1999 XJ that is lifted 4.5 inches. It is my daily driver and hardly if ever goes offroad (for now). I am running the stock ecco rims with 31x10.5x31 tires. I want a little bit wider stance (for stability and looks). I was wondering what you guys would recommend for Backspacing and rim...

I am looking for a set of four (five is better) 15x8 rims for my 1999 cherokee with 4 inches or less of backspacing. I do not have much cash right now, but have lots of stuff to trade. Like new chest freezer PS2 (Playstation2) with 4 dual shock remotes, memory card and 20 plus games...

Anybody know of some good junkyards in Michigan perferably close to Lansing with a nice variety of XJ's? There are quite a few yards around here, but they want high dollar on everything. Thanks, Denton

Just wanted to share. if you wanted to know what a Rough Country 4.5 inch series X lift kit (bought on here through Grimus99xj) looked like on a 99 xj with 31x10.5x15 with stock rims. Sorry for the Poser shots, I will try to add more photos later

I just bought these on here to install on my 99 XJ. I just wanted to make sure this is all the required hardware to install properly. Also is there any good write-ups on installation of Factory Tow hooks? I know you have to take off the bumper and such, just want to make sure. Thanks everyone!

Tell me what you have and how much $$. Thanks, Denton

What do you have? Thanks, Denton

Will ship on buyer's dime. Paypal Accepted Front drivers window switch will fit 97-01 $15 U-bolts for a dana 30 or 44 axle will fit lifts up to 6 inches brand new $20 Front blinkers will fit 97-01 $15 Front sidemarker lights will fit 97-01 $10 Radio will fit other years $15...

I was wondering if anyone knows if a Mopar roof tire carrier for a 1994-1998 ZJ would work for my 1999 XJ? Thanks alot

I installed a B&M super cooler with trans temp guage. I also ordered a additional sending unit so I can monitor both incoming and outgoing transmission temps. I need the coupler that reduces the top thread of the 3/8 compression t fitting to the sending unit i believe it is (1/4 npt). I seem to...

I have a 1999 XJ, just lifted 4.5 inches with transfer case drop and 6 degree shims in the rear. I have a constant humming/ maybe a vibe between the speeds of 30 and 40 mph, I think it is coming from the rear. Could this be a ujoint? Or am I!!!1 trying to get around the slip yoke driveline...

I recently just installed a B&M supercooler and Guage. I have the sender located in the return line, but I also want to measure the output line as well with the same guage. I was wondering if I could just buy a universal sending unit? Also what would you suggest for a switch? I have heard you do...

I just installed a B&M supercooler with a B&M trans temp guage on my 99 XJ. (Thanks to all the help on this forum) I put my cooler after the radiator in the trans return line. So I go trans->radiator->cooler->trans. I also installed my gauge on the return line 4 inches from where it goes in the...