Search results

Hello all Blew up engine back in March. Due to the current unpleasantness, the build and swap took a little longer than I had planned. The engine has been in the jeep for over a month at this point and it will not run correctly. It will crank and run after some extended cranking. Once...

Good morning, I have a couple of jeeps with mismatched ignition/door lock cylinders. I am able to re-key the ignition cylinders, but I am wondering if anyone has a source for the tumblers? I can tear down a few old cylinders, but I would prefer to buy new if possible. Thanks

Anyone watch this yet? https://www.hoonigan.com/blogs/build-battle-season-01/build-and-battle-ep2

Short version: I have a no start after a lower end rebuild. Engine turns over, has fire, has compression, has fuel pressure. It occasionally pops back through the throttle body when trying to start. Longer version: I have a Golen stroker circa 2007 currently (not)running in a 2000 XJ. Engine...

Hi, I'm hoping someone can help me. I need to know which flexplate is which. I am concerned that I mistakenly put a Renix flexplate into an HO jeep. I have several flexplates here, and I know they have a different number/spacing for the spaces on the reluctor ring, but I can't seem to get a...

This isn't mine. I really wish I could afford it. I wanted to put it on here so that maybe someone who would appreciate it would see it. https://atlanta.craigslist.org/atl/cto/d/1988-jeep-cherokee-comanche/6442578516.html

Hi, I'm rebuilding the Golen 4.6 stroker for my DD. I have a Hesco aluminum head that I'm going to install while its on the stand. I'm wondering if anyone has any experience with the head, and can recommend a particular head gasket to use. I removed the head from another jeep in the middle...

Hello, I'm hoping some one had run into this issue. 1988 xj 4.6 stroker cuts off when hot. After about 15 or 20 minutes, it stops dead. Still getting fuel. Got frustrated and changed cps, ignition module and coil. Still having issue. Anyone have any suggestions about what to look at...

Thereason is a video put out by jeep to show how good the grand cherokee was of road against its competitors. I think it was the wj, bury I could be wrong. The was an explorer, a blazer, and a few others there. I'm on mobile and I'm really having trouble finding it. Anyone know the video...

Hi, I have a Warn or Belleview winch I would like to sell or trade for a modern winch. I don't have the ID tag, so exact ID is tough. Belleview called them a 6000#, Warn says they were good for 8000#.It is in pretty good overall condition and it runs. I do not have the cable controls. It...

Hello, I am having trouble finding one part for an 01 XJ. The piece over the license plate. In 00 and 01 it was available in chrome on the Limited. Does anyone know what it its called? Sounds silly, but I can find the rest of what I am after pretty easily but not this one. Thanks

Hi, I have an old belleview winch that I am putting back into service. The motor works, I have all the gears/parts but I cannot identify the two roller bearings on the middle gear shaft. Doeas anyone have a parts list or happen to have the part number for the bearings? Thanks

Just a quick thread showing what I've been working on. The specs are as follows: 1990 block 1998 head Comp cam (cannot remember the number off hand. Built it 5 years ago) Comp Lifters (MISTAKE! they are lound) 1988 4.2 crank .30 Sealed Power pistons I pulled it out of my daughter's TJ...

http://im1.shutterfly.com/media/47a3d833b3127ccef30c3080e49900000030O00BbMm7NyxcNQe3nw4/cC/f%3D0/ls%3D00508193726020130612144120719.JPG/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Pretty straitforward. Does anyone know the thread pitch for the oil filter adapter on the block side? Its a Renix era block, if it matters. Sorry, I've searched, but I'm at work, and would like to order a part today, and I'm hoping someone knows. Thanks

Posting this in this forum because it is a 4.6 Golen stroker. 2001 XJ sport Ok, I have been getting a CEL with code 1351 (cam, crank disagree) off and on for a couple of months. I have replaced the CMP and the CPS, several times on the CMP. I think I have found the issue. The teeth on...

Ok, I recently installed a new to me Golen motor in my DD street oriented XJ and I have run into an issue. Like the title of the thread says I need brakes. The stockers are marginal with a stock setup XJ, and with the engine in place (and a host of other mods yet to come) the factory...

So I am lowering one of my Cherokees a little. I am going to swap the rear to SUA using durango/dakota/s10 springs. I am wondering if anyone knows how much a set of stock front TJ springs will lower the front. I can adjust the rear to match. Thanks

Hi, I recently aquired a rather used Warn 8274 in some parts trading. I hooked some jumper cables up and got it to pull in and out after jigling the switch wires on the solenoids. Now, after making a set of cables, and building a bumper, I cannot make the solenoids work, even with jumping...

Looking for some input, or ideas here. My mother in law needs a car. Through circumstances out of her and our control, she is not able to buy one at the moment. So, I am thinking my wife and I will buybuild her a Cherokee. The problem is, I have a daughter turning 16 in two weeks, and I am...