Search results

Here is my '00: http://stlouis.craigslist.org/cto/4787768251.html

Ok I have done some searching and research. I have found some very good leads, but nothing sounds close to what I am looking for/at. When I bought my latest Cherokee Sport, the PO had claimed that the pinion nut had come off. I got with the XJ, the rear driveshaft and axle yoke. I also got...

Yesterday the family went out for the morning. We loaded up and drove about 2 hours or so, with intermittant stopping and starting, with the first errand we ran I left it idling for about 30mins or so. By the time we were done, we drove back home, shut it down and came inside. We had noticed...

I recently replaced front axle u-joints with new units that have a cap drilled for a fitting. The fitting that came with them has a slot for a slotted screwdriver, and looks like its kind of depressed to fit a grease gun adapter. I thought my needle adapter fit them, but did not. I bought...

I broke one of the three 12pt 13mm hold down bolts for my wheel bearing assembly. Are these a readily available part, or Junkyard only?? Jeff

I just got done replacing the passenger side axle shaft u-joint. Of course in getting the old one out, I mashed up this ring or collar thing on the outer shaft. Is it really needed?? If so, where is it sourced?? That stub shaft doesn't seem to need it as it uses the rest of the face of the...

I am in need of a cheap(even if parts need rebuilt), but complete and useable Dana 30HP from a pre '00 XJ. I live near St Louis, so meeting shouldn't be a problem. I am needing one to swap out with my LP30 in my '00 XJ. Let me know what you have and how much. Free is good too, if that is...

I am looking for some photos of anyones stock exhaust on their 2000+ XJ exhaust, at the very rear of the Jeep. I have a stock replacement hanger that I am needing to see just how it is supposed to go into place. I will try and post up a picture in the morning of what I have and where it...

I cannot for the life of me remember what size the socket that is needed to pull the drain and fill bolts out of the transfer case is. Can anyone enlighten me so I can repurchase the one needed?? Thanks in advance, Jeff

Vehicle is my '00 XJ Sport. Jeep has 182k on it. Did a head swap back in the end of March. A/C hasn't really worked on this Jeep since I purchased it back on Halloween of last year. I went to the parts store today and got 2 cans of 134 and a hose to add it. When I connected the hose to the...

I have a '00 that I really need the drivers seat, but if someone is either parting one out or upgrading their seats, I'm interested. Mine is the darker grey(charcoal) color. Pm me what you have and we can go from there. I'm tired of doing the lean to the right rear direction. My behind is...

I have a question here. When I hit a decent bump at highway speeds, the Jeep has like a delay or roll before returning to straight ahead, or the direction the wheels were pointing(if it occurred when the vehicle was turning). Since I am used to leaf sprung front and rear axles this is kind of...

Got my heads swapped and in the process of bolting on the intake and exhaust to it. Old head that was on the jeep had dowels for the intake. New one does not. Can I use a dowel to line it up and torque the bolts to specs?? From there will it work loose again, or be an issue at all?? Also...

I am starting this writeup on the eve before the start of pulling the head on my '00 Sport. I have read some of the threads here and on other sites and I have come to the determination that either the head is cracked or the head gasket is blown on my 4.0. While I was somewhat hesitant on doing...

Here are two of the plugs after I pulled them to see whats going on within the engine. This one is of the #1 cylinder:

Here is where my '94 4.0 is at as of this afternoon. I finally got the dizzy stabbed to a 5 o'clock position per se. Its starting, and running, but I don't think its quite there just yet. Upon locating my timing light, I fired the Jeep up and the light hits at the mark between 8 and 15...

Okay I have just replaced the pump and strainer on my '94. The O-ring was on the tank side of the sending unit/pump assembly. Is this where it is supposed to go?? I have tried putting the retainer ring, and assembly into place numerous times, and I have yet to get it "lined up" per se. I can...

Once I get my issues on my '94 4.0 AW4 situated, I am starting to tweak it for more mpgs. My last '94 got a consistent 18mpgs with 30" BFG AT's, no lift and an AirRaid Throttle body spacer. While the spacer was to help pickup some power and mpg, it did the power not mpg. My first mod this...

Ok got the CPS changed out on Saturday(after not getting the correct part from the stealership). Set it up, still cranking but no spark. Also no pressurization of the fuel rail. I'm starting to go bald with some of the hairs being pulled out. Cam sensor/pickup coil next, or coil?? I will be...

I got back into another '94 4 door, actually the same color scheme as my last one(red/black Sport). The specs are a 4.0, AW4, 242, D30, 8.25. The Jeep only has 165k on the odo, which is about what my last one had. Since my DD car is on the fritz, I am needing to get this beast running. I...