Search results

I'm looking for the door panel clips for the rear lift gate on my 96 XJ. For some reason I can't find any that fit at AZ, checker etc. online I found some yellow ones that are listed for a 98+. Anyone have a p/n. Looked on eBay, quadratec, rock auto, etc Thanks

I have been looking for the clips that hold the "door" panel on the rear interior hatch of my 96 XJ. Every one of them was trashed by the time I got them out and I have not been able to match anything up at the parts stores. Anyone have a P/N for one that fits? Thanks for your help

I have a stock 96 XJ 4.0 with about 192,XXX on it. I wanted to post a good experience with a part, hopefully someone will benefit from it in the future. I know you can spend hundreds of dollars on starters, hi-torque etc but this is just a basic starter. I purchased it from Checker in August of...

I have read a bunch on the "no start and NSS" which is why I managed to get as far as I did today but Im still puzzled. stock 96 XJ 4.0 AW4 about 190K, ill try to keep it simple Went to leave for work, no crank but plenty of voltage from the battery. I had my girlfriend try to crank it while I...

Here is a link to where this started with a pic: http://www.naxja.org/forum/showthread.php?t=1076116 I jacked up the pass side of the axle and it was nowhere near the bump stops yet and it wasn't even close to threatening the tranny line against the oil pan, so I starting looking elsewhere. I...

Quick update: This is on a 96 XJ 4x4 pretty much stock. I have put on all new tie rod ends, ball joints, u joints, track bar, steering stabilizer, UCA and LCA bushings...i think that sums up the front end. I have been feeling movement somewhere in the front end over bumps (on the road, not 4x4)...

Im pretty sure my 96 XJ's alarm was dealer installed in 96. When I worked at that dealership (00-03) they were installing "silencer" brand alarms. The alarm in my jeep has 5908P on the front of it (the zero could also be an "O"). On the back it has FCC ID: ELVMR5C. There is no brand name on the...

Is the TRE at the pitman on a 96 XJ LH or RH threads? I am finding conflicting info and trying to order the part from work today thanks

Ive been reading around for awhile and cant find for sure what im looking for. My 96XJ has a D30, for the ball joint replacement, is there a split ring that I need to install? Someone had a 93 with one and an 87, then another post said that it doesn't have 1.... Just trying to clarify and plan...

Does the UCA bushing flange seat AGAINST the axle "doughnut" on the DRIVERS side? Stock 96 XJ 4X4 D35. Im trying to track down a "pop" on the drivers side somewhere. The pass side one looks good but im wondering if my drivers side one backed out a little, the flange is not against the axle...

Im sure its been done. My D35C in the rear of my 96 has the "pop" in style drain plug and id like to pull that out, thread the housing cover and add a screw in plug. I just wanted to get an idea of the thickness of the housing so I could figure out what I was going to need before I tear it...

I have power to all of my locks (4 door) but there isn't enough juice to actually fully unlock the passenger door or either of the rear doors. The drivers door is the only door that always unlocks with the keyless and the passenger door will work occasionally. The rear doors havent worked since...

I just recently put new axle u joints and upper and lower ball joints on my jeep and ever since there is a low pitched moan from my front end, I notice it at very low speeds when turning right and braking slightly. While I was under there I shot all of the tie rod ends etc with grease. Any clue...

96 XJ sport 4.0 Its been in the 40's here in AZ in the mornings which is cold for us. I have about a 40 mile drive to work in the AM and up until about a week ago my jeep ran right at about 210* on the freeway once it warmed up. For about a week now, on my way to work, it never gets any hotter...

I decided to start with these since I don't have too much cash just yet. For U joints I was going to use the Spicer 5760X for the axle u joints and Spicer 1310 or 1330 u joints for the drive shafts. That is my first question, do I need the 1310 (3 7/32" wide) or the 1330 (3 5/8" wide)? Are all 4...

I finally have a little extra $ to put into my 96 cherokee. Its pretty much stock but I want to put a little money into the front end. Upper and lower control arm bushings, sway bar bushings, new track bar, etc. Ill also be replacing the u joints and ball joints while im in there. A few...

I am looking at going through costco for my BFG A/T's 235/75/15 for my stock 96 Cherokee. They will not put the "oversized" tires on my jeep so I will just take them my 4 wheels (not a big deal). 115.99 per tire They quoted me $553.86 out the door, mounted and balanced. Im not looking for the...

96 cherokee 4.0 4X4 all stock suspension except the shocks When I turn the wheel all the way to the right and roll forward, I can hear something binding and then it sounds like a spring coming "unsprung." Any ideas what is causing this? It sounds like it is coming from somewhere on the right...

I don't go to the dealer unless I have to, I thought they pretty much had me by the ba!!s with the abs light coming on so I took it in. 96 cherokee 4.0 auto 4X4 Yesterday they called me back and said, "its the ABS relay" Fine please put a new relay in and take care of the ABS light Todays...

I was hoping for a big difference after putting on some new shocks but Im not feeling it. To be honest my cherokee rides kind of like crap which Im bummed about. It does feel a little better than it did with my old shocks though. What else should I look into besides shocks that might help? Its a...