Search results

Trouble I had is that every one of them broke when I took the panel off. I assume they were the original clips and the AZ heat COOKS anything plastic like that. I don't think I have ever heard of OSH.

I'm looking for the door panel clips for the rear lift gate on my 96 XJ. For some reason I can't find any that fit at AZ, checker etc. online I found some yellow ones that are listed for a 98+. Anyone have a p/n. Looked on eBay, quadratec, rock auto, etc Thanks

I have been looking for the clips that hold the "door" panel on the rear interior hatch of my 96 XJ. Every one of them was trashed by the time I got them out and I have not been able to match anything up at the parts stores. Anyone have a P/N for one that fits? Thanks for your help

I have a stock 96 XJ 4.0 with about 192,XXX on it. I wanted to post a good experience with a part, hopefully someone will benefit from it in the future. I know you can spend hundreds of dollars on starters, hi-torque etc but this is just a basic starter. I purchased it from Checker in August of...

I have read a bunch on the "no start and NSS" which is why I managed to get as far as I did today but Im still puzzled. stock 96 XJ 4.0 AW4 about 190K, ill try to keep it simple Went to leave for work, no crank but plenty of voltage from the battery. I had my girlfriend try to crank it while I...

Good deal, thanks. Any other thoughts if the bump stops, motor and tranny mounts dont seem to be the issue? How else would this tranny line crush? Im off to the parts store for CCV and tranny line repair parts...

Here is a link to where this started with a pic: http://www.naxja.org/forum/showthread.php?t=1076116 I jacked up the pass side of the axle and it was nowhere near the bump stops yet and it wasn't even close to threatening the tranny line against the oil pan, so I starting looking elsewhere. I...

Anyone know the total length of the stops? Or have a PN? Im going to try NAPA and a few other places tomorrow to see if I can finish this tomorrow. Thanks

Alright thanks for the help guys. Ill order some from quadratec and hopefully have them in before the weekend...or maybe just after the weekend. Ill let you know how it goes. Thanks again

Pucks are actually vulcanized rubber, not hard plastic just FYI(15 years of hockey under my belt :P). That sounds like a nice quick fix but im not sure I want to go that route. Im wondering if I could lift the jeep by the frame, place the new bump stop in the sleeve, shim the remainder of the...

Well son of a Be-otch. I did some quick searching on bump stops, it sounds like I have the press in type. Without removing the coil springs, can I get the rubber out and some how press the new ones in?

Quick update: This is on a 96 XJ 4x4 pretty much stock. I have put on all new tie rod ends, ball joints, u joints, track bar, steering stabilizer, UCA and LCA bushings...i think that sums up the front end. I have been feeling movement somewhere in the front end over bumps (on the road, not 4x4)...

Nice write up and pics. I need to tackle this along with my valve cover gasket and oil filter eliminator I get lost every time I brave the "injector swap" search. Lots of info but also confusing as F***

Thanks for the link, My remote looks like the one on this page (4th one down, the gray one with one black and 1 blue button): http://www.aboutsecurityconcepts.com/Silencer_Security_s/68.htm

I looked into replacing the whole line when mine started to leak. Guys here said to cut and clamp so I cut the whole rubber line out, bought some multi-purpose line and 2 hose clamps and called it a day. Ive got 7,000-10,000 on it with no issues

Im pretty sure my 96 XJ's alarm was dealer installed in 96. When I worked at that dealership (00-03) they were installing "silencer" brand alarms. The alarm in my jeep has 5908P on the front of it (the zero could also be an "O"). On the back it has FCC ID: ELVMR5C. There is no brand name on the...

Thanks for your help

Is the TRE at the pitman on a 96 XJ LH or RH threads? I am finding conflicting info and trying to order the part from work today thanks

Ive been reading around for awhile and cant find for sure what im looking for. My 96XJ has a D30, for the ball joint replacement, is there a split ring that I need to install? Someone had a 93 with one and an 87, then another post said that it doesn't have 1.... Just trying to clarify and plan...

Cool deal I put all new bushings in, just making sure it wasn't supposed to seat all the way. I hand grenaded the threads on the stock bolt so I replaced it with a normal bolt, same size Thanks as always for the help