Search results

Hi guys, I have a Cherokee Dana 44 rear axle I bought from another NAXJA member years ago that I never installed. It has sat in my garage covered all that time and is in excellent clean condition. It has factory gearing, but I put a new Ruff Stuff diff cover on it, and I also bought a Ruff Stuff...

Hey guys, I’ve had a Cherokee 44 sitting in my garage now for 8 years and I think it’s time to put it in. I have a truss for it that needs to be welded on, shock relocation brackets that need to be welded on, and I’ll need gears, a locker, and I’d like to put disc brakes on it. The Dana 35 in...

Hi all, I have a Rigidco rear bumper for sale.It has all the upgraded stainless steel options, standard end pieces,tire carrier for 35" or smaller, gas can carrier, hilift jack carrier, and the new version latching system.I bought this new direct from Terry at Ridgid for my 96 a little less...

Big Doh! here, went to add a quart of what I though was Mobil 1 motor oil to my 4.0 HO engine, and when about a third to half a quart was in I realized it was Mobil 1 75-90W gear oil.Shit, always wear your friggin glasses.Anyway should I not worry about it, or do a complete oil change

Does anyone happen to know the exact size wrenches to remove the front drive shaft on a 96 XJ?My wrenches are either to small or to big, and I don't want to strip those little bolt heads.Also any tips would be appreciated. Thanks.............Chris

I have a pair of Dick Cepek Super-Offroader 100W halogen lights for sale.These are new unopened in the box.They are the stainless version with clear lenses.These are the same lights I've reliably run on my rig for 10 years now(see bottom photo).Asking $50.00 for the pair.PM me or call me at...

I have two sets of brand new, never used 3/4' D-Ring shackles.One set are the standard Warns, and the other the heavier duty USA 6 1/2T.Both are the standard for us 3/4 7/8" pin.Asking $25.00 per set.PM me or call 949-559-6639 and ask for Chris

Have a set of Rubicon Express Extreme Duty fixed upper control arms here out of my 5.5" Extreme Duty lift kit.Asking $75.00 PM me or call 949-559-6639 Chris

Have a Rubicon Express Extreme Duty Track Bar here, the one with the superflex joint.Very low road only miles on it.Except for some grease and the typical rust colored threads its in perfect shape.Asking $100.00.PM me or call 949-559-6639 ask for Chris

Hey all, here is a couple pics of my conferr roof rack where its rusted pretty good.What would be the best way to repair this spot.Thanks!

Ok my powertrax no-slip is in a HP D30.Going slow around corners and especially in and out of parking stalls its pops and you can feel the whole front end shift.Its scaring the piss outta my wife and people standing close by when it happens.Didn't do it the first couple hundred miles, and after...

Just a plug for Hellbilly Bill, the guy risked his life welding me up a cool new tracbar and over axle mount in the rain :scared: We'll be drilling out the pitman arm to 3/4 and dropping the draglink this weekend.Thanks Bill!

I have a new rattle noise, not real bad yet, which seems to be coming from the vicinity of the transmission tunnel.It seems to be most noticabe when I let off the gas going over 30-40 mph,The only thing I've done recently in that area is install RE upper adjustable superflex control arms.I...

I just put alloy chromoly shafts in my Dana 30 which required pulling the brakes off of course.Now everything is back together and woks fine including stopping, but the brakes now squeak a little bit when I'm doing a slow rolling stop.Its not bad but still annoying.They were quiet before the...

I just renewed and since its been along time since I was red, don't have my Den password.How do I get the password, and will I get a new NAXJA sticker in the mail?All my information is the same as last time I was paid up.Thanks Chris

I just swapped in some Alloy chromoly axle shafts into my Dana 30 and am wondering what I should do with these rusty axle nut retainers.Are these retainers something that can be ordered new somewhere, or should I try wire brushing em and spaying with something like Rustolem rust reformer.I do...

Ok I'm red again, and my PM's magically started working again too party1: I was wondering how I go about getting a a So.Cal. chapter decal if there is one. Thanks.........Chris

Ok, you have a set of 35" MTR's on Detroit locked axles on your rig with lets say 7000 miles on em, you rip the side walls on one of em wheeling, but luckily you have the no questions asked warranty so no problem, you get a new replacement.My curiosity is when does the tread height difference...

Ok I want to modify my wiper blades by replacing em with Rain-X blades :D. I've searched and read my Chiltons.Seems my wiper blades are not the same type connector as in the book.I need to get the old ones off, but don't want to break or bend anything.Could you guys look at these photos I shot...

Has anyone ever used Offroad Evolution in Fullerton for any fab work?I've got a TNT D30 truss on order, and need someone to cut and grind off the stock uca axle mounts and then weld the truss on.Any other recommendations for someone who could do the job in Orange County?Thanks in advance!