Search results

I am going to sell of my project. It seems crazy, but I am hoping to start a new one eventually, and am not going to have a chance to wheel it this summer hardly at all. Seems a waste. NOTE: The whole rig is not for sale! I am keeping parts for my next project. I will list what is included in...

Does anyone know of a schematic of the measurements of a cherokee frame rail? Like a CAD drawing with measurements, or of anyone that has taken the time to really measure it all out accurately? Just wanted to see if there was something floating out there before I take the time to lay under my...

Me and my club homies went out to Gilbert MN to get some pre-Moab testing done. Everything worked great, I didnt roll, and nothing hugebroke- so it was a great weekend! My only carnage was busted loose rock rails (Time to weld them on for good) one lock out (Cheap plastic warn) and a bent...

I am proud to say that by the weekend I will be a member of the "have a running and working rig" ranks again! I finally got my jeep put back together so I am ready for memorial weekend in plenty of time. I got the front HP44 installed and rolling. Look at all that clearance! Thanks to Bill for...

So the guy that wanted to buy my half doors backed out. Silly... These are now up for sale and I would much rather not have to ship them. I bought doors from the local yard for $230, and I figure I have a lot of time and matrials into them. So I am asking $350 obo. A good set of tube doors is...

I figured I would add a littel tech for the sake of those that have asked about my doors in the past. You will need a spare set of doors from the junk yard, or a big set of cajones to cut up your stock doors. I started with junk doors and cut up my stock ones later.... Step 1: Gut your doors...

I have all of the motor/regulators out of my 97 doors. Both the front and rears, both sides. I want $30 for each one or we can work a deal if you want more than one of them. Shipping will obviously be your responsibility. Please email me if you are interested. I dont check back here too...

How does the front door latch mech work? I need to change the way my half doors open since my current way uses hte stock handles and they basically got smushed and almost ripped off on my last trip. So, does the lever need to be pushed down or up in order to get the latch to pop open? I already...

I have both sides available to sell as I just gutted my old doors from my 97. Someone needs these I am sure. I also have both wiring harnesses available as well. $85 a side regulators $50 a side wiring Drop me a line at [email protected] if youre interested as I dont get back here...

My friend Bob is trying to fix his wife Jill's jeep after DCT and looking for spare shafts. Does anyone know if the lengths change at all from TJs, XJs? Do the lengths change at all between the two? Or are all of htem basically the same minus leafs/coils mounts? Thanks for hte help, BOB thanks...

I am thinking about adding some more tube to my rig. After this... I realize basically ALL of the damage that happened could have been avoided if I had a little more tube on there. I am generally not a big fan of EXO cages, so I am doubtful at best, but wanted to see what you guys thought... It...

I am basically out of room in my engine comp to fit a wiper fluid bottle. I have a 97. I bought an older model that is smaller than my stock one, and I dont think it will fit and I would need a new motor for it since hte older motors have different connections than mine. So, curious if you guys...

I built some half doors for the front of my rig. Until I have the rear ones done the same way I would like to be able to roll the windows down. However, I think when I removed the front doors and all thier wiring it seems they automatically put on the override for the rear windows. Now they wont...

I have a 97 so it came with a factory tranny cooler. I mounted my winch low and deep in my new bumper so I need to move it. It is mounted via two small screws on the crossmember between the rails. Has anyone relacated theirs before? Where to- and how did you do it? Do I just need to get some...

Hey fellas, I chopped the back off my rig, and now have it caged in. I am a bit nervous about the rear quarters now... They are boxed in with a steel frame, but it will not be enough to lean them up against anything. So, I am looking for ideas and suggestions to give them some support. If you...

I am in the middle of assisting the build of my cage. It has been a lot of my ideas mixed with a lot of the builders ideas, and we need some help. Basics: It's a combination between exo and internal. Main section for safety is the internal cage. A, B, and C pillars are all getting feet welded to...

I moved my ARB compressor so now its close enough to use a SS braided line. Both of the ends on the SS line are female, so it connects to the compressor fine, but the end that goes into the front housing looks like this, and I need find a way to get the a fitting like this that will fit into the...

I need to build a traction bar to help cover these new big meats. Where can I buy one good jonny joint, or RE style joint that would do well on the end of it? Should I get one of curries? I also need two bushings and the round stock to put them in. Where can I get those? Can I use a stock...

I am a fool, and sold my seat bases with my old seats. Now I need a set to mount my new seats to. Does anyone know where I can get a set for a 97? j

I am planning on moving my gas tank up into the bed. Just cutting a hole in the bed section, dropping in teh stock skid, and just moving up the lines. Building a basic box around it, calling it good. Just gaining some clearance. Fill hole is the quesiton. Obviously cant run it to the same spot...