Search results

I guess the millenials have taken over this site. You know the ones that think the computer you plug into your car fixes it too..............

So, this is the second "re-furb". for my 1990 2dr sport. About 10-15 years ago I did did a complete suspension overhaul RE 3.5" w/ swing shackles, RE adjustable track bar (heim) shocks, tires, paint, all the usual engine mods etc. I have just completed some much needed repairs. New floor...

Does anyone know off hand what the size of the stock inverted flair on the clutch master cylinder is?? I have a 1990 with 4.0l and Ax-15. It's a hard line not the flex line.......Thanks

Thank you. I haven't been able to find the pic.. I am guessing that you just weld it up so that the rod LOA (after mod) equal to the stock rod LOA??.....

I've got a 1990 with the ax-15/5spd.I replaced clutch flywheel master, and slave around 3yrs ago with a luk clutch/slave & flywheel. I bought a parts store master cylinder which has just failed leaking. Wanting a quality replacement I've discovered the Howe Masters. After extensive searching...

Looking for the rear RH LH Quarter Panel Applique for a 1990 Cherokee sport 2dr..........must have good mounting studs........Thanks

Thanks for the reply's the glass shop's didn't pan out........for those looking for Auto Fasteners I found an online supplier Northern Fasteners . biz.......... Thanks

Hope everyone is enjoying there summer wheeling........as for me I am finishing up my 1990 sport project, and am having trouble finding the windshield moulding clips..Aka the little plastic clip that holds on the trim.......my local dealership saying discontinued.......any help would be...

anyone? I can't seem to find online for this vehicle......

Hello all, Anyone have a Right Rear Lower Quarter panel?? It's for a 1990 2dr Sport.....Just finished with the rocker fix and noticed lower quarter was rusty....i would like to weld in a fix before re-spray........ Thanks

:patriot:Thanks for all the replies..........I will do the spot priming on the areas that I did some metal work......I will ask the paint store about a sealer as recommended(sometimes they just want to sell stuff even when not needed) .....Thanks for the advise on VOC's......I have Sprayed the...

Hello, Any paint guys out there that could recommend a primer.........I am going to prime over well sanded factory paint, then top coat with Nason ful-thane single stage .....I would like to use a Med/High build sand-able primer...There are so many different systems I'm just not sure what to...

I am getting ready to give my 90 XJ 2 door a fresh coat of paint.....I am going to weld in new rockers which i already have.......i am looking for the PS rear lower quarter......anyone know where i can get??...online?????...i plan on removing the factory roof rack......all the bolts are rusted...

My 2000 has done this and it was a faulty CPS

Hey Guys, I am having a problem with my 2000 xj the fuel pump is not getting power.. I have checked the #11 fuse, and also the relay in the power distribution center.... all seem fine Just looking for possible cause and what to check next..... Thanks

Last summer i converted my R12 ac to the r134a sytem with the DIY conversion kit......My question is about checking the oil level in the compressor.....How to do it??? when i did the conversion the r134a said with lubricant oil on the can.....The problem is the AC is working but has a rumble...

Anyone got an electric fan blade they want to get rid of......I need one for a 1990 4.0 xj.....my motor is still good just have cracked blades>>>> Thanks.....

Thanks, But i was looking for the down pipe that goes from the exhaust manifold to the cat......

Where can i buy a good exhaust down tube for a 1990 XJ 2dr 5spd manual?? The exhaust manifold and the rest of the exhaust is stock??? Any recommendations??

According to the method you discribe i have about 12 degrees of "stretch"....it confirms what i already expected with the "rattle".......Thanks