Search results

I pulled the pan to replace the rear main seal and at the bottom of the pan was a single roller bearing. Its just over 3/4" long and 1/4" in diameter. Its not a magnet and it is hardened. I cant for the life of me think of where this would of come from. There aren't any roller bearings in...

Does anyone know the part number to that clip or where to get one? Wrecking yards around my area are slim pickins.

Hi all, Short and to the point. I am trying to resolve a pulling to the right issue on my stock '96. I had an alignment done, toe was out a bit and they dialed that in but it made no change to the pull. Rotated tires around as you would normally try, brakes aren't dragging and the steering box...

I have some 1.5 " lift blocks and a set of stock MJ shackles which if I remember right will give 1/2" above stock XJ ones. Also have a few angle shims, some crappy cast aluminum ones and some nice 6 degree solid steel ones from Tom Woods. Blocks $10 Shackles $10 All 4 shims shims $10 Please...

$100 www.ksl.com/index.php?nid=218&ad=11734433&cat=&lpid=1&search=jeep

I need one or two tires for my ghetto trailer. Would rather have 235's but what ever you may have, let me know and how much $ Thanks, Brett

Had in incident with our trailer and bunged up the rear door of our Astro van dutch door. I need a replacement for the drivers side dutch door. Anyone know of someone parting one out? Thanks, Brett

Had in incident with our trailer and bunged up the rear door of our Astro van dutch door. I need a replacement for the drivers side dutch door. Anyone know of someone parting one out? Thanks, Brett

How the heck do you make a gate panel? Do I have to make an internal frame? I can visualise the istall of the gate and can figure everything out but it puzzles me about the gate. I don't see that a gluing is an option. What I am working with is a 8' fence with rails and 1' tongue/groove...

My wife wants me to make her a coat rack hanger for Christmas. She wants it to have a metal panel above it to hang the kids school/art stuff with magnets. I need somewheres around 2' X 4' or close to. Even an old metal shelf panel would work but it needs to be flat. What you got? Thanks in...

I have some 3 feet wide by at least 15 feet long rubber mats that are 1" thick. I want to cut the width so they will fit on the side of shed for weed control but with them at 1" thick they are exactly easy to work with. Another thing is that they have a fabric weave in them also for...

Which shaft is longer, the driver or passenger side? Brett

In my ongoing search I found a '97 TJ D30 complete. I am wondering if the hubs will work with my axle from my '92. He has the rotors to. Are all TJ's low pinion or is it the same as XJ's. I guess what I am asking, would this be a LP or HP (the guy didnt know). If worse came to worse I could...

Will a hub unit from a D30 '04 TJ fit my '92 XJ?

If your tank is bone dry does that cause the fuel pump to "shut off"? I got a ZJ I am looking at and the guage is on E. Normally you can hear the pump run momentarily to pressurize the system. We put in what gas we had in the tank which amounted to nothing but maybe .25 gallons. There is...

My friend here at work has a 96 ZJ with a auto tranny problem where it won't shift out of 1st gear. I am wondering if the computer would be the same as my '92 XJ where I can pull the codes with the key. Or would there be any codes from the tranny? Also a side question, if your tank is empty...

Will having a shorter then needed trackbar and having your axle shifted to the driver cause it pull right and wear the tires improperly?

Anyone have these packs: http://cgi.ebay.com/ebaymotors/jeep-cherokee-xj-rustys-6in-rear-lift-springs-tj_W0QQitemZ8036177276QQcategoryZ33585QQrdZ1QQcmdZViewItem Weird shaped. I just put some on like this but haven't wheeled with them yet. It put the pinion in the right spot for my SYE.

http://sell.ksl.com/cgi-bin/classifieds.pl?db=miscautos&website=&language=&session_key=&search_and_display_db_button=on&results_format=long&db_id=59536&query=retrieval Good luck however, they are in "good condition" so she might have a chance.

Trying to get some ideas where/how to mount a tire carrier to my bumper. Trouble is that the bumper only sticks out at most is 1/2" and that I have a receiver in the middle of the bumper. I want to put a tire carrier on but I dont want to have it swing close and cover the receiver. I have an...