Search results

OK boys and girls, what changed with the 07 dana 44 so it wont fit. I was under the imprecion that the short cummings were fixed. I havent loocked at one yet, not many rubys new orleans. I need to replace my old 30, and a 44 would be a nice. I did search but didn't find any thing. So what...

I got a folding step stool from HSN. Tied on a string to pull it in. Works well for my 60+yr old Mom.:party:

I replaced the tps and that helped. It,s due a tune up I'll do that next week. Also replaced the motor mounts (they were blown) with mounts from Rusty's. Man are those mounts stiff, the jeep rocks when I rev it alittle. But I can realy feel engen vibs. I still need to replace the tranny mount...

I searched but cant find the thread. I know this has been done to death. I degreased to find the oil leak, I used Gunk all over to clean it real good then hit it with a power washer. Looks perty. Now she runs like crap, stumbels rough idel, no power, hard shifts and died once. So is it the cps...

I ran 31's for a few years and realy like them. noise isn't to bad, tread wear not bad either, and you just can't beet the price. The only problem I had (my falt) was a little delamination, cause I drove with to low of tire pressure for a month. I check tire pressure alot now. If you can get the...

My rear axle seal just started leaking after regearing. I know it's a simple fix. But i was told that someone makes a sealed bearing. Is that true? If so who makes it. I have to pull the bearings anyway might as well upgrade.

Nevermind I found a shop that will do it for $225 an end. Thanks for the input.

So anybody in southeast Louisiana willing to help with this. I'll get the beer and poboy's.:wave:

I just did this monday. You need from jks the hub spacer, the tie rod and drag link. the stock wj ti rod and drag are too long. 2000+ XJ/TJ hub/ unitbearing, early 1999- hubs sit out further. 1999+ WJ rotors re-driled to a 5x4.5 pattern. The rest is in the write ups. Good luck. My setup did...

Like I said I don't mind paying, but is a $53hr jump fair just for getting my own parts. I understand it's a buisness. And they have so much work that they need change their posted labor rate to run off a client. Sorry for the sarcasm. You are trying to help thanks.

I forgot to say this is is my dd, and can't have it down for for more than a day.

Well I had work done at two of the shops for other stuff and on one bill it was $47 hr x 2hr for labor. Thats a $53 jump in labor. I don't mind paying for somthig if I can't do it my self but that much of a jump in labor is wrong. Unfortunatly I live in a townhouse and don't have space for a...

Anyone in the New Orleans area know how to set up gears, and would be willing to help? I have both sets and rebuild kits, but I don't have the tools to do it rite. The few shops around here that woud do it with My parts want $600+ per end. That's $100+ pre hour, @%#*&% outrageous, and they say...

I wanted to have the "stars and bars" painted on the roof of mine, in shades of grey. But the manager of the shop flat out refused, said I needed to be racally sensitive. My for farthers fought under General Lee. Southern pride We lost I know.:laugh3:

I thought about that but I don't have a lathe. also thought about just cutting and weld without the bar. :dunno:

I'll give them a call. Thanks for the help. I almost have all the parts. It's going to be a full day once I get started, no help to speak of and this is my daily driver.

Thanks for all the help. I did a test fit today with the WJ rotors and 2000+ unitbearing. Every thing lines up well enough. The rotor is 1/16' off center of the caliper bracket, but has good clearence. A thin washer should center it but as of now I'm good. I need to grind a little of the top of...

Ok. I got the WJ rotors, there at a machien shop now. I'll pick them up in the morning. I also picked up a 2000 XJ hub. So I'll test fit again tomarrow. Thanks for all the Help

Well Darn, I was hoping that I could reuse my old bearings.

FrankZ What size spacer did you make. Dose the unit hearing make that much of a difference?